guy bishoff
  • Male
  • Lethbridge Alberta
  • Canada
Share on Facebook
Share

Guy bishoff's Friends

  • Bruce Peers
  • Gregory  Sawka
  • Wayne Huk
  • Thomas G. Griesemer Sr.
  • Conrad Watters
  • Joseph Begany
  • Bill Alexander
  • Lawrence Van Egmond
  • Dave Van Dyke
  • Glen Brown
  • Joe Harrington
  • Robert Reinero
  • Travis Corbin
  • Dwayne Roos
  • Mark Townsend
 

guy bishoff's Page

Profile Information

Aircraft Model
STOL CH 750
Project Status
Just started
Building From
Plans-only
Building Experience
Have already built an airplane
Flying Experience
Private Pilot

guy bishoff's Photos

  • Add Photos
  • View All

guy bishoff's Videos

  • Add Videos
  • View All

Comment Wall (11 comments)

You need to be a member of Zenith Aircraft Builders and Flyers to add comments!

Join Zenith Aircraft Builders and Flyers

At 9:15pm on February 18, 2016, Bruce Peers said…

Thanks Guy.....Zenair said the same thing when I ordered it...so I will avoid extra weight and time and not use it.....Bruce

At 9:49pm on February 17, 2016, Bruce Peers said…

Hello Guy: I got some Zinc Primer for the corrosion resistance (grey) but with the RV 9A, we used Zinc Chromate (Yellow)....any idea if this is a key difference or even if you recommend this spray resistance or something entirely different?  Bruce

At 8:50am on December 26, 2015, Bruce Peers said…

Thanks for the friend request Guy....I would love to come down and visit you guys some time....to see the three you have flying and to see your works in progress......Merry Christmas....your paint scheme is awesome....Bruce

At 3:46pm on September 7, 2012, Bill Alexander said…

Guy

The ducts are from Aircraft Spruce ,its been a while now but I think the part # is 05-00859.

I cut the part off that went to a hose and made a box from sheet metal and riveted to the NACA inlet. Then cut the hole and glassed to the cowling. The box holds a K&N type filter element from Rotax. It was kind of a waste to only use less than half of the material in the duck-but that the part I needed. 

One inlet is fresh air to the Rotax air box to the carbs- the other is air to the heater shroud and then to carb heat or cabin heat.

Regards Bill

At 9:04pm on August 6, 2012, Conrad Watters said…

Guy, thanks for noticing the seats. I agree.

They were made by Donovan Thompson, 905- 380-4388. His shop name is' Hole In the wall'. I believe that he is now working in Burks Falls, Ontario.

Donovan did an excellent job, cost was reasonable. The fabric was aviation quality and the foam was the higher level foam which adapts to the shape of your wallet and buttocks. I have found that it was especially worthwhile for longer flights. Sorry, but I could not find the name of the particular foam but would be glad to track it down if you would like.

Good luck with your fleet.

I am looking at the feasibility of attending the Dawson City flyin for next June. Perhaps, I will get to see a little of Alberta.      Conrad

At 8:00am on May 22, 2012, Jim Derickson said…

Guy, I don't have a picture that shows the detail. I used 2 l angles from the panel to the firewall and made a H frame to support the back of the radio trays, the bottom L angle ,the horizonal one I made longer to pick up the glove box. I also made the verticals longer and tied a piece of stainless rod to form a bow for strength and provide a wire run to tie to. I will try to scan a drawing and send it to you, Jim

At 7:25pm on January 24, 2011, Joseph Begany said…

Guy

I have spent a ton of time looking through you and your firneds build pages.  In mostcases on these pages I am a little jealous of the progress so many have made on their projects but in your case I would give anything to have some local frineds involved and building together.  How awesome for you guys!!!  I wan to make a die for the flanges on my lightening holes.  Gus built steel dies  Your dies look like aluminum.  Are your dies aluminum?  If not, do you think aluminum would work?  I don't have a hydraulic press but I can get to a mechanical press.  Are any of you working?  You sem to be able to get together quite often.  Good luck and post more video.  I plan to video as much of my project as I can.  When you do your videos you should comment on what it is you are doing.  It could save a lot of typing!!!  Take care.

 

Joe Begany, Elyria, OH

At 11:38am on July 22, 2009, Robert Reinero said…
Thanks Guy,

I understand the licencing issues and just wanted to take the time to thank you for answering so quickly. I am a three time plans only builder, two long Ezes and a 601X. I also have the 701 plans but it turns out to be to small for me and my son, we are booth 225 lbs and 6'2". The 750 looks just about right!
Would you be able to send a PDF of the layout of the parts on the raw aluminum sheet, that in itself would be a great help.
Bob
At 6:25pm on July 19, 2009, Robert Reinero said…
Guy,
I am a plans only builder and would like to know if I can get the CNC directions for cutting the parts on a water jet from you? I would be happy to contribute for the information.
At 1:40pm on June 9, 2009, Glen Brown said…
Hey where'd you get that red thing? Crackerjack box?
F Liar 5
 
 
 

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...

                                                     

Weather Maps


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, power distribution panel, Approach Fast Stack harnesses, Dynon and Garmin avionics, and more.


Custom Upholstery Kits for your Zenith Aircraft:

Zenith Vinyl Upholstery Kits


Zenith Apparel from EAA:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

Aircraft Insurance:

 
 

West Coast USA:

Transition Training:

Pro Builder Assistance
 

Pro Builder Assistance

Aircraft Spruce & Specialty for all your building and pilot supplies!

© 2019   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service