"Sold the 701 W/912 purchased a 750 stol 3300 jabiru this engine is all new to me."
Zenith Aircraft Builders and Flyers
Online Community of Zenith Builders and Flyers
-
David McCusker
- Male
- Iva, SC
- United States
- Blog Posts (4)
- Discussions (10)
- Events
- Groups
- Photos
- Photo Albums
- Videos
David McCusker's Discussions
Flygas intake manifold
Started this discussion. Last reply by Bill Alexander Feb 16, 2016. 7 Replies 0 Likes
Was wondering if anybody had experience with the fLygas intake manifold for the rotax 912 it has a very large crossover tube it's supposed to eliminate carburetor synchronization.
Engine runs rough when landing
Started this discussion. Last reply by Juan vega Dec 1, 2015. 6 Replies 0 Likes
Hey all my 912 rotax ul runs rough when landing its ok above 3000 rpm. from 2200 to 3000 rpm its shakes on the ground. New plugs and wires sync. carbs not sure what to check HELP!!!!Continue
David McCusker's Page
Latest Activity
Flygas intake manifold
Was wondering if anybody had experience with the fLygas intake manifold for the rotax 912 it has a very large crossover tube it's supposed to eliminate carburetor synchronization.
"Hey thanks everybody just wanted to put this out there the carburetors were out of sync. appreciate all the help"
Engine runs rough when landing
Hey all my 912 rotax ul runs rough when landing its ok above 3000 rpm. from 2200 to 3000 rpm its shakes on the ground. New plugs and wires sync. carbs not sure what to check HELP!!!!See More
Rotax running on after shut down
Hey all its me again Im tring to get the bugs worked out of this plane. Does anybody know why my 912 rotax 80hp keeps running on for about 15 to 20 seconds after I turn the key off. My idol is around 1900 rpm at shut down but continues on at 350 rpm for a short time. It just started doing this last week. I sure could use some help. Thanks againSee More
Water temp Rotax 912UL
Hey all I have a 912 Rotax 80 hp anybody know what the max water temp is. And where do i install a temp sender thinking I might want a gauge for liquid temp. Thanks See More
Prop Pitch
Anybody have info on prop pitch I have a 80hp rotax 912 with GSC 3 blade wood 68 inch on my 701 with low RPM 4400 is max. Wondering what degree i should use at the tip for short field takeoff and more RPM. ThanksSee More
Rudder Boots
Anybody know what I can use to cover rudder pedal arms in firewall maybe rubber boots cold air burrrrrSee More
Profile Information
- Aircraft Model
- STOL CH 750
- Project Status
- Flying
- Building From
- Purchased finished aircraft
- Engine installed (or plan to install)
- Jabiru
- Building Experience
- Have worked on airplanes before
- Flying Experience
- Sport Pilot (or Ultralight)
- Home Airport (ie. KMYJ)
- KAND
David McCusker's Blog
Rotax running on after shut down
Posted on April 11, 2015 at 3:04pm 4 Comments 0 Likes
Hey all its me again Im tring to get the bugs worked out of this plane. Does anybody know why my 912 rotax 80hp keeps running on for about 15 to 20 seconds after I turn the key off. My idol is around 1900 rpm at shut down but continues on at 350 rpm for a short time. It just started doing this last week. I sure could use some help. Thanks again
Water temp Rotax 912UL
Posted on April 5, 2015 at 7:33pm 3 Comments 0 Likes
Hey all I have a 912 Rotax 80 hp anybody know what the max water temp is. And where do i install a temp sender thinking I might want a gauge for liquid temp. Thanks
Prop Pitch
Posted on December 8, 2014 at 9:44am 3 Comments 0 Likes
Anybody have info on prop pitch I have a 80hp rotax 912 with GSC 3 blade wood 68 inch on my 701 with low RPM 4400 is max. Wondering what degree i should use at the tip for short field takeoff and more RPM. Thanks
Rudder Boots
Posted on November 5, 2014 at 6:30pm 4 Comments 0 Likes
Anybody know what I can use to cover rudder pedal arms in firewall maybe rubber boots cold air burrrrr
Comment Wall (1 comment)
- At 7:30pm on September 25, 2014,
Steven Winn said…
Nice looking SkyJeep!
New from Zenith:
Classified listing for buying or selling your Zenith building or flying related stuff...
Custom Instrument Panels
for your Zenith:
Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, power distribution panel, Approach Fast Stack harnesses, Dynon and Garmin avionics, and more.
Custom Upholstery Kits for your Zenith Aircraft:
Zenith Vinyl Upholstery Kits
Zenith Apparel from EAA:
Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz
Builder & Pilot Supplies:
How to videos from HomebuiltHELP.com
Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.
Pro Builder Assistance
Aircraft Spruce & Specialty for all your building and pilot supplies!
© 2019 Created by Zenith.Aero.
Powered by
