Sebastien Heintz's Blog (145)

Part 25: Installing the "Upgrade Package" to our Zodiac CH 601 XL: It's now all back together!

We've been finishing up the aircraft these past few days, continuing on where we last left the project.

We've re-installed the flaps and all the controls in the aircraft, as well as reconnected all the wiring and fuel lines.

Above, Steve and Roger finished riveting the last rivets back in...…

Continue

Added by Sebastien Heintz on December 24, 2009 at 2:30pm — 6 Comments

Part 24: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Putting it all back together...

As you all know, we've been busy making the producing the parts of the Upgrade Package kit, and now we're also busy shipping them out to builders and owners!

All the Upgrade Package kit parts and hardware shown above can be shipped in the two cardboard containers: One box (18"x12"x6", 25 lbs.) for the smaller parts and all hardware and one 6-foot long 4-inch cardboard tube (about 16 lbs.) for the longer parts. These package are… Continue

Added by Sebastien Heintz on December 18, 2009 at 5:26pm — 7 Comments

Part 23: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Re-Installing the Center Spar in the Fuselage

Continuing on where we last finished, now we re-install the "upgraded" wing center spar section into the fuselage and position additional fuselage doublers:



First we installed the beefed-up Front Wing Uprights (6-ZU-2-6). This replaces the original Wing Uprights (6B13-1) with the heavy duty .125-inch Front Wing Uprights. We are forced to drill a new row of holes parallel to the original row for the new… Continue

Added by Sebastien Heintz on December 14, 2009 at 4:00pm — 8 Comments

Installing the "Upgrade Package" to our Zodiac CH 601 XL: Riveting and Re-Assembling the Center Spar

I've now added the photos for the last post on riveting and re-assembling the center wing spar section. Below is the upgraded center spar section, ready to return to the fuselage:



As previously mentioned, Roger Dubbert from the Zenith factory will be attending Gus Warren's Zodiac CH 601 XL… Continue

Added by Sebastien Heintz on December 9, 2009 at 3:49pm — 3 Comments

Part 22: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Riveting and Re-Assembling the Center Spar

After having positioned, drilled, and clecoed the upgrades to the center wing spar assembly, we now rivet the parts back together and bolt the two halves of the center spar assembly back together to reinstall it into the fuselage.

Here we begin to rivet the center wing spar assemblies back together using the "conventional" bucked rivets:…

Continue

Added by Sebastien Heintz on December 5, 2009 at 5:00pm — 4 Comments

Part 21: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Installing the Upgrades to the Center Spar

We already disassembled the center spar section (a while back).



Now, we'll get to the task of installing the upgrades and reassembling the the center spar. We have posted the latest Upgrade Drawings as they have been updated (albeit still in draft):

We position and backdrill the… Continue

Added by Sebastien Heintz on December 4, 2009 at 6:15pm — 7 Comments

Part 20: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Aileron Mass Balance

Continuing where we left off yesterday, now we install the mass balance to the ailerons. Since this was mandated by the UK LAA earlier this year for Zodiac XL owners there, we used their drawings (which was engineered and tested by the LAA), as specified in the AMD Safety Alert.



The aileron mass balance consists of an 18-inch arm… Continue

Added by Sebastien Heintz on December 3, 2009 at 5:30pm — 7 Comments

Part 19: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Working on the Ailerons

With the main wings done, we now focus on the aileron upgrades.

The aileron upgrades consist of three separate items: Aileron gussets (65W2-5 and 65W2-6) on the aileron ribs, L-angle stiffeners for the aileron trim servo, and finally, aileron mass balance. Above, the right aileron is shown. Below is the left aileron.

Our demonstrator Zodiac CH 601 XL airplane has the original "hingeless" aileron system - many customers have the hinged… Continue

Added by Sebastien Heintz on December 2, 2009 at 5:00pm — No Comments

Part 18: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Working on the Second Wing

Now we're working on finishing the second (left) wing.

We debur and rivet the aileron bellcrank support channel and stiffeners, and the rear channel doubler...

And we bolt in the wing root doubler 6-ZU-1-2 and rivet the nose rib angles (6-ZU-1-3 and 6-ZU-1-5) in place...

...and we cleco and rivet the nose ribs in place. Note that in the photo we are… Continue

Added by Sebastien Heintz on December 1, 2009 at 11:30am — 4 Comments

Part 17: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Finishing the First Wing

Now that we've installed all the upgrades to the first wing, we still need to finish a couple of items to the wing. With the wing skins clecoed back in place, we measure and mark off the 20 mm. hole placement for additional rivets into the inboard main wing spar (top & bottom):

We drill a hole between the existing holes...

Basically, we're doubling the number of rivets from the front and rear… Continue

Added by Sebastien Heintz on November 30, 2009 at 8:30pm — 2 Comments

Part 16: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Installing the L-angle stiffeners to the top of the rear skin

We've made excellent progress over the past holiday weekend finalizing the drawings and verifying the parts. The wings are done and the center spar section is being verified.



As mentioned earlier, Gus Warren of FlyWithGus.net has announced that he will be hosting a Zodiac CH 601 XL "Upgrade Workshop" at his facility in Edgewater, Florida the second weekend in… Continue

Added by Sebastien Heintz on November 30, 2009 at 4:30pm — No Comments

Installing the "Upgrade Package" to our Zodiac CH 601 XL: Using an Angle Drill Attachment

As we've installed the "Upgrade Package" to our Zodiac CH 601 XL we've been using the same sheet-metal hand tools that are used in building and assembling an aircraft from a standard kit. One needed new tool is a right angle drill or drill attachment. We have used this extensively with the upgrade package to drill out rivets and to drill in the new parts.

While a… Continue

Added by Sebastien Heintz on November 27, 2009 at 3:58pm — 8 Comments

Part 15: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Installing the Spar Wing Root Doubler (take two)

As shown previously (in Part 8), we had already installed a Wing Root Doubler (6-ZU-1-2) to the front side of the spar root, but as mentioned earlier (see my Part 13), a new Wing Root Doubler (6-ZU-1) replaces the previous doubler. This new doubler is cut… Continue

Added by Sebastien Heintz on November 25, 2009 at 5:30pm — 1 Comment

Part 14: Disassembling the Center Wing Spar Assembly and more...

As most of you know, we're now accepting orders for the Upgrade Package kit. We're not ready to ship the kits just yet, but we're getting everything organized so that we can ship as soon as the kit installation has been verified and documented, and that all the needed parts are in stock. We're prioritizing availability to first ship to those builders who are ready to install the Upgrade Package kit parts. We ask that those of you who are not ready yet to install the upgrade package to let us… Continue

Added by Sebastien Heintz on November 24, 2009 at 4:39pm — 4 Comments

Part 13: Removing the Wing Center Spar Section

Again, I want to thank Doug and Lori from Quality Sport Planes for organizing and hosting the free "Upgrade Workshop" this past weekend at their facility in Cloverdale, California (shown above). This was an excellent opportunity for Zodiac XL builders, owners, and pilots to learn about new upgrades, and how to install them. For more information, contact Quality Sport Planes at… Continue

Added by Sebastien Heintz on November 23, 2009 at 5:36pm — 3 Comments

Part 12: Installing the L-angle stiffeners to the rear bottom wing skins

Now we install L-angle stiffeners to the rear bottom wing skins:

This is an easy job with the top rear skin removed. We trim the L-angle piece to length, pre-drill it, and then drill and cleco it into the bottom rear skin:

We'll share the position measurements and exact details with the final drawings. The Upgrade drawings are nearly finalized (which will allow us to then release and… Continue

Added by Sebastien Heintz on November 20, 2009 at 4:30pm — 10 Comments

Part 11: Installing 3-position LED lights (and replacing the AeroFlash / Whelan strobes)

Since we have full access to the insides of our wings we decided that this was the perfect time to upgrade to new LED (light emiting diodes) lights. Note that this is not part of the Upgrade Package prescribed in AMD's Safety Alert and the FAA's SAIB - this is just an opportune time to install them (and also allows us to save a few pounds in the process).



This is the original Aeroflash-Signal anti-collision/position light assembly (nav/strobe light) on the left wingtip:…

Continue

Added by Sebastien Heintz on November 19, 2009 at 4:30pm — 4 Comments

Part 10: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Replacing the Fuselage Rear Wing Attach Plates

Here we move over to the aircraft fuselage and center spar section. Roger reviews the draft drawing 6-ZU-3.

Again, remember that the posted drawings are in DRAFT form and we are currently finalizing them...

We'll be replacing the original rear wing attach plate (6B5-4) with a heavy-duty 1/8-inch 6-ZU-3-5 Attach Plate. This is the plate that sticks out the sides of the center fuselage and that bolts to the wing's rear channel. Note that the… Continue

Added by Sebastien Heintz on November 18, 2009 at 4:59pm — 6 Comments

Part 9: Installing the "Upgrade Package" to our Zodiac CH 601 XL

Picking up where we left off in our last post, here we drill and bolt the cap spacer 6-ZU-1-6 centered between the original spar web 6W3-1 and the new wing root doubler 6-ZU-1-2:

Then we start deburring and riveting some of our Upgrade Package additions permanently into place, starting with the back of the wing, riveting the Top Rear Spar Angles and… Continue

Added by Sebastien Heintz on November 17, 2009 at 5:30pm — 1 Comment

Part 8: Installing the "Upgrade Package" to our Zodiac CH 601 XL: Installing the Spar Wing Root Doubler (beta)

Now we install the Wing Root Doubler (6-ZU-1-2) to the front side of the spar root:

The Wing Root Doubler is a flanged piece that sits in front of the spar:

We decided to drill out the existing inboard noserib and replace it so that we could drill the Wing Root Doubler flange well into the noserib flange (the replacement noserib will be supplied as part of the Upgrade Package kit):…

Continue

Added by Sebastien Heintz on November 16, 2009 at 6:00pm — 3 Comments

Monthly Archives

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service