So can someone tell me the trick to mounting these tubeless tires, how does a guy get the o ring to stay on the wheel half while bolting the two pieces together. I used to do tires for a living and I'm confused, I'm thinking tubes. Kevin  P.S Matco wheels

Views: 723

Reply to This

Replies to This Discussion

Kevin.

I just finished installing tubes in mine. Everything was fine until it wasnt. Right main went flat, twice ,so I ordered the tubes from Matco. and put it in the right main only. Two weeks and again the right main is flat along with the nosewheel. ( insert anger here). turns out the right main was pinched, and the O ring in the nosewheel was broken in half. For me, tube was the way to go even though I have talked alot of people who have not had any problems with the tubeless installation. Mine had been on the wheels for a year before the problems and only after 20 hours on the airframe did the problems come up. No real hard landings either. :).

Tom

Kevin,

On mine I (contrary to the directions) bolted the wheel halves together first. Then I put some liquid soap on the o-ring just to help it be a little slippery, and stretched it over the rim carefully. Once past the rim it snapped into place in the crevasse of the wheel right where it belonged. My tires have been mounted for about a year and a half (and now with about 50 hours flying time on them) and still no leakage or problems. They hold air at least as well as my car tires do. A little liquid soap diluted with water on the tire bead before installation makes the tire go on easier, too. 

Good luck, and keep building; it's worth it!

Randy

Randy, So you mounted the tire on the wheel just like you would a car tire, didn't think of doing it that way, I was just worried the o ring will dry rot over time. thanks, Kevin
2 out of 3 of mine leaked the first time I put 'um on, called Matco for advice...suggested I use Vaseline on the O-rings, did, worked fine with no leaks for 5 months now. Regarding installing the O-ring, I put the O-ring on after bolting the halves together.

Kevin

      I heated up the O ring in hot water and with a little Vaseline I slipped it over the hub. Its been a almost a year in the garage with no evident leaks.

             Rob M 

It looks like all of you guys did it the same way. When I read the directions I thought there was no way it would work the way Matco said to do it. Thanks
We used tyre mounting soap and held the ring off on the slope whilst we put it together - took 2 and a half people! Rings in place over one year with no issues - even with bush landings (see http://medicineonthemove.org/trailer.html and look at the 701 sequences).  Looks like there is more than one way to ring a hub!
I got the tires mounted today. I mounted the tire on the two halves first, tighten down three bolts, set the wheel on a short 2x4 (stem side) then slip the o ring over the back side, while pushing down on the tire. Kevin

You sir are a genius.  I fought with these for a bit until I saw your post and it worked like a charm.  Thank you.  

Richard

Years ago, I was the first to reply to this post. In that post, I stated I used Vaseline on the O-ring and that it was still holding as time went on. Not long after that post, I continued to have consistent air leaks and put tubes in all of my tires. 13 years later, I’m still flying the plane and all is good. Have never had a flat, have replaced the main tires once due to wearing them out, and have over 1000 flight hours and 2700 + landings. With tubes, there is no guessing game as to whether they will hold air or not. Just my 2 cents on the topic.

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service