Has anyone tried one of these with a zenith kit?

https://www.youtube.com/watch?v=23B_LZPddoo

Do we know if the nose pieces can be modified?

Views: 460

Reply to This

Replies to This Discussion

Have you ever got this working?

Love it.  Gotta have it.  Will save you and your forearms.  The tips that I received from Zenith with the concave heads did fit the tool.  I understand Zenith will also take a set that you send to them and grind/turn the appropriate shape into the head.  I bought one late into my build.  Works great.  

Fred;

Thanks for the information.

I have some M12 Milwaukee tools. Good to know the Zenith heads fit.

I will add it to my collection since I won't have to worry about compressed air for a rivet setter.

Thanks again;

Keith

I use this gun and it’s awesome!
You can’t modify the Milwaukee nose piece as there is a cavity below the surface that holds a ball bearing (that grips the rivet and stops it falling out)

It took me a while but I found a nose piece from a long arm rivet gun that fit. And I shaped those and it works great.

It’s possible that an air rivet gun nose piece may fit?

I bought the Milwaukee Rivet Gun before starting my build...I'm way more than pleased with it.  I did have a bit of a learning curve...there is a small ball bearing secured in each nose piece with an O-ring.  That ball bearing puts pressure on the rivet stem to prevent the rivet from falling out of the nose piece; however, when the rivet is pulled, the rivet stem stays in the barrel/neck of the rivet gun.  When I would insert another rivet, sometimes the stem of the newly inserted rivet would jam against the previously captured rivet stem.  I would have to take the barrel/neck off the gun and remove the jam...not difficult, but frustrating.  The solution was to remove the o-ring and ball bearing...after doing that, the rivet gun has been trouble free pulling thousands of rivets:

A pneumatic rivet puller is a bit faster...but, as far as I'm concerned, not having to listen to a compressor cycling on and off...and not having to drag an air hose around my work area far outweighs the minor decrease in pull speed.

I machined the Milwaukee nose pieces using an SE-5 Carbide Bur.  I didn't have any issue with the nose pieces being too hard to machine...the carbide bur cut the material without any problem.

The nose pieces for the manual rivet puller in the picture (DeWalt Swivel Head) are NOT interchangeable with the Milwaukee M12 rivet gun.

Thanks I guess Ill try to machine my puller heads, i have spares on order.

Question:  Does the M12 pull rivets slightly slower or "more gently" than a pneumatic rivet gun?

The reason I ask, is that I have the typical pneumatic rivet gun that Zenith sells.  It worked great, but one day I was riveting a piece of aluminum that had been powder coated.  The rivet holes were drilled after the powder coat process, so of course that broke the seal of the powder coat.  When I started to pull rivets with the pneumatic gun, I noticed a ring of blistered-up powder coat around each pulled rivet!  My theory is that the pneumatic gun pulls the rivets so quickly, it creates a tiny blast of compressed air around the rivet head as the "domed" or rounded head is formed.  This tries to escape through the broken seal of the powder coat, lifting up the powder coat.

Of course, the obvious solution for me was to pull the remaining rivets with a manual rivet puller and I had no further problems.  Just wondered if the pulling action is a little slower or more deliberate on the M12? This might also prevent some of the little "smilies"/dents/dings that can result if the pneumatic puller recoils and bounces off the surface around the rivet.

John

N750A

With the Milwaukee riveter, it's a steady and strong pull.  I guess you could say it's BOTH slower and more deliberate.  There is still some recoil as the rivet stem breaks; however, I find it much easier to control than the quicker pop and recoil of a pneumatic gun.

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Custom Upholstery Kits for your Zenith Aircraft:

Zenith Vinyl Upholstery Kits


Zenith Apparel from EAA:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Golden Eagle Aviation

Pianosa Flying Farm

Aircraft Spruce & Specialty for all your building and pilot supplies!

© 2021   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service