Does anyone have experience with installing an 0-320 vs an 0-360 Lycoming in a Ch 801?

Curious on how a 320 may perform.

Thanks

Views: 584

Reply to This

Replies to This Discussion

It would all depend on the O-320 you installed. Since you are not worried about certified requirements you could use any number of "hot-rodding" options available for the O-320. Even a certified O-320 can have an STC'd high compression kit installed that makes it a 160HP engine. A PowerFlow exhaust supposedly adds ten horsepower. There is a certified and legal 170HP right there, in an engine that weighs a bit less than a stock O-360. Now, if you start adding various uncertified things like electronic ignition, cylinder head porting and polishing, etc you could get even more power. Basically the O-320 would have a slight weight advantage over the O-360 which would partially offset the lower power output. Then you could add power to the engine and actually increase performance. It all depends on how creative you want to be and how much money you want to spend.

A final consideration - O-360 cores are expensive because so many RV series planes use them and demand is high. O-320 cores will cost you a lot less as a beginning to build on.

Have fun!

Thank you Bob! I appreciate the info. I did not know about increasing an 0320. I find it a little hard to find out info on the CH 801 and that really helps

Glad to help, even if in general terms only. Another point to consider is -- those hot rodding options are available for the O-360 also. So, if you started with an O-360 and boosted the performance of that engine you would have a real rocket ship. A stock O-360 gives pretty good performance already. A hot rodded O-320 would most likely match the stock O-360.

Final thought - a constant speed prop adds weight and complication but greatly improves performance since the full rated power of the engine is available for take off and climbout and for cruise. An O-320 with a constant speed prop would most likely outperform an O-360 with a fixed pitch prop. Again, life is full of trade-offs. There are some interesting electronically controlled uncertified constant speed props available now that would go nicely on either an O-320 or an O-360. They weigh less than the certified ones and don't have the weight and complication of a mechanical prop governor, as well. Also, you can fit one of the electronically controlled ones onto an engine that is not equipped to mount a conventional constant speed prop and governor combination.

A fixed pitch prop is kind of like a one speed transmission in a car - you can have good low end performance (lock the transmission in first or second gear, a climb prop) or you can lug like heck at take off and climbout and then go faster once you get to altitude and start cruising (lock the transmission in third or fourth gear, a cruise prop). A constant speed prop lets you take off in first gear (fine pitch blade angle), climb out in second and third gear and then shift into high gear for cruise (a coarse blade pitch to bite the air effectively at high speed). That lets you have better performance on less power because you can use all the horsepower in all flight situations. A fixed pitch prop can only let the engine develop full power in one part of the flight, the rest of the time it is not being efficient.

Great information Bob! I would have never thought of a CS prop on this build , but  it makes sense. Best of both worlds. I think the 0 360 is probably the right choice. I was thinking cost when I really should be thinking performance. Thanks again for sharing your knowledge.

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service