The upper wing skins over the fuel tanks in my 701 are held on with sheet metal screws. The plans call for rivets, which would likely be much stronger and lighter, but I guess the builder thought screws would make the skins easier to remove if he ever had to service the tanks. He thought wrong. 

Now I'm trying to figure out how to remove about 250 painted-over phillips head screws that are starting to rust. After fifteen minutes of effort I haven't been able to turn a single one.

Does anyone have any bright ideas? So far the tips I've found online are along the lines of "scrape off the paint and give it a good whack with a hammer".

I've resigned myself to ruining the paint job - are there any paint strippers that are known to be safe on 6061-T6 aluminum?

In the meantime, I'm going to try a heat gun to see if that helps. 

Thanks

Views: 575

Reply to This

Replies to This Discussion

As far as the paint gluing the screws in place, one trick is to get  a cheap set of hole punches (like those used to punch holes in a leather belt, etc.) and try to find one that's the exact diameter of the screw head and use the punch to cut the paint around the periphery of the screw head being very careful not to nick the aluminum panel.  I've also found that sometimes a JIS (Japanese Industrial Standard - has sharper corners on the bit vs a Phillips) screwdriver will grip some Phillips-head screws better and is not as prone to strip them out.  If you think the corrosion is making the screw more resistant to remove, then definitely try a penetrating fluid (obviously the paint will have to be cut for it to get to the threads) and let it work for a while before attempting removal.

They actually make JIS screwdrivers that you do whack on the handle and it twists the bit like an impact gun, - they're great to remove screws from the engine on an old Honda motorcycle, but a wing isn't strong enough to resist that kind of impact and you'd wind up ruining the structure of the wing!

If you have to strip the paint, auto body supply shops sell a paint stripper called "Klean Strip Aircraft Ultra Paint Remover."  Wear a respirator if you use it, it's very potent!

On my 750 STOL, I guessed that I might someday need to access the fuel senders (which turned out to be true when they both started leaking years later) so I painted my top wing root panel separately and after fueling the aircraft for the first time and letting it sit a day or two to ensure no leaks, I then riveted the panel and touched up the heads of the rivets with paint.  Drilling out rivets is relatively easy and apparently much easier than removing corroded screws!  The panel came off easily and since it was painted separately, there was no paint "gluing" it down and no paint disturbed in the removal and reinstallation.

John

N750A

Thanks, John, those are great tips. I hadn't heard of JIS before - I'll see if that shape grabs any better. 

Your idea of painting the tank covers separately is genius.

Drilling out rivets is pretty easy, so if anyone else has screws in their wings, replace them with rivets before it's too late!

I would get one or two screws out nicely and look very carefully at the hole size and condition of the aluminum underneath.  As you mentioned rusting screws it seems very likely that you will find corrosion from dissimilar metals under the screw head.  If you are fortunate enough to avoid that, it sounds like the holes may well be oversize for riveting back together….  In either case you are stuck replacing a larger section of material, so getting the rest of it off neatly may not really matter…..

Just my 2 cents

If Matt lucked-up and the corrosion and/or hole enlargement/distortion wasn't very much, perhaps the rivet holes could be upsized such as going from an A4 to an A5?  However, as in all things concerning modifying major structures, a consultation with Zenith would be in order!

That's what I was thinking, but I'll have to cross that bridge when I get to it. 

If you stick with screws, spend the extra bucks for stainless steel screws for reassembly. They are much less inclined to rust or glue themselves into place. Also, place a nylon washer under each screwhead - this greatly reduces dissimilar metals corrosion by seperating the aluminum from the stainless steel.

If anyone is considering screws for a new build, I cannot strongly enough recommend stainless screws with nylon washers under the heads. I have been using them for many decades and almost never have a stuck in place screw. I do have the luxury of hangaring the plane(s) most of those years, but some of them lived outside and did just as well in my experience.

Here's an update in case anyone else is looking for a solution to this or a similar problem:

After trying several different things, the only product that really worked for me is called Vampliers. They're pliers with serrated jaws that are designed to grab the head of the screw, and wow do they work! I stumbled across them while looking for something else online and I'm sure glad I did. They work on most of the screws right away, but for the most stubborn screws I carefully grind a bit off opposite sides of the head with a Dremel cutoff wheel and that creates more surface area for the Vampliers to sink their teeth into.

I see there are hundreds of five star ratings for these things on Amazon, and I'd agree. The price/value ratio is excellent considering the number of hours of frustration they're saving me.

Sorry, I didn't see this thread until just now.  Too late to help, but...

Completely agree about the vampiers!  One of the best tools I have ever bought.  One of my Beechcraft buddies recommended them and they are great at getting the corroded screw out of a 70+ year old airframe.  Maybe a touch expensive, but completely worth it. 

Also if you are worried about messing up painted on screws, there are specialized paint cutters for various sized screws.  See https://www.aircraftspruce.com/catalog/topages/screwpaintcutteran8.php  I have never used them, so I can't say how well they work.  Might not be useful on some screws.

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service