At Airventure, I expressed interest in the new Zenith "Donut" nose gear suspension system and Roger recently provided me with a kit to retrofit my STOL 750 so I could provide an early evaluation and testing (Zenith has been testing this in-house for a year).  This system will also be available for the Cruzer and the 601/650.  The 701 system will follow, but apparently it will need some modifications from this design.

The original bungee system works well, but it does have a single-point failure potential (the bungee!) and apparently the last few years the production process has changed and bungee failures are occurring more frequently.  In addition, the bungee is non-adjustable for pre-load and induces some torsional resistance when the nose gear rotates.  

My kit arrived Friday and was very complete - the only additional material needed was some white lithium grease to lubricate the area where the donuts are located (3M silicon grease is now recommended - doesn't dry out like white lithium grease does).  A detailed drawing and step-by-step instructions were included (note correction on Page 2 about spacer above last puck).  The total weight of the installed parts was 3.5 lbs (this is with one steel collar - the second collar is removed after pre-load adjustment).  The bungee and bungee pin removed were 0.5 lbs for a net weight of 3 lbs. Here's what's in the box:

I removed the nose gear by cutting the bungee and detaching the steering rods and lower bearing.  I had the stubs that hold the bungee on the upper end of the nose gear cut off and the resultant holes welded shut. (You can modify your own nose gear, send it to Zenith for modification, or purchase a new nose gear.)  I powder coated the lower, exposed portion of the nose gear (not required, but something I had wanted to do the next time the nose gear was off!), painted the area from the steering arms up to 10" from the end of the upper gear leg, and ground and profiled the welds to provide a smooth surface. 

I polished the upper exposed 10" with a #80 aluminum oxide abrasive disc backed by a foam pad (so as to conform better to the curvature of the tube).  It is important to polish the tube and profile the welds so the donuts can slide smoothly.

The kit includes 10 spacers and 10 rubber "donuts" or pucks that are stacked above the 2 steel shaft collars.  I found the spacers and donuts to be a tight fit, so I opened them up slightly with an oscillating spindle sander.  The sander removed very little material from the donuts, but easily opened up the spacers so they could slide on the tube without binding. The spacers and donuts are then stacked on the nose gear (start with a spacer, then a donut, and alternate, finishing with a donut).  The rubber donuts fit snugly, but will slide with a little lithium white grease for lubrication (white lithium grease was initially recommended, but now Zenith recommends 3M silicone paste grease). I then drilled and riveted the front and rear angles to the upper stop.

These 8 rivets were drilled out in the forward firewall gusset on each side and opened up to #12 holes with the upper stop cleco'd in place.

After deburring and Cortec application, the upper stop is bolted in place with 16 AN-3 bolts - heads inboard and nuts outboard. The nose gear is then reinstalled and the stack is pre-loaded by tightening the lower shaft collar, prying up the upper collar with screwdrivers on each side, and then tightening the upper collar.  I then loosened the lower collar, moved it up, and repeated the process for a total compression of between 3/8"-1/2".  Some pre-load is necessary to permit the self-centering of the nose gear in the lower bearing.

Apparently I got the pre-load about right - when the aircraft sat back down on the nose gear, the steering arms rode approximately 5-6 mm above the bearing block, allowing for easy ground steering.  As I mentioned earlier, once the pre-load is adjusted, the second steel collar can be removed. (One is sufficient and they weigh 1/2 lb each!)  Zenith will eventually have an adjustable tool to adjust the pre-load and the second collar will no longer be necessary at all. With one shaft collar, Roger recommends Loctite on the securing machine screws.

My original bungee system worked great.  It was smooth and I couldn't even detect the self-centering "notch" as I swung the rudder from one side to the other. (IMHO, most rudder smoothness problems are due to over-tensioning the cables.)  However, I was amazed at the difference after installing the new "donut" system!  The suspension feels more compliant and is quieter. Steering effort on the ground was reduced and in the air, the rudder pedals were extremely light. However, when the rudder was centered, it seemed to hold it's position well.  The best way I can explain the difference in "feel" is it is similar to the difference between manual steering and power steering - it feels like the nose gear is turning on ball bearings - there is absolutely no torsional resistance!  I always felt my finger-tip dual stick forces were much lighter than my rudder, and now they are equally light.  After flight testing and bumping along on a turf strip, I checked the bearing marks on the grease on the strut below the bearing and it appears the gear was deflecting about an inch during landing and taxi, which is fairly similar to what I saw with the bungee.

About the only negative is the additional weight over the bungee, but that's a small penalty to pay for eliminating the potential single-point failure of the bungee and eliminating regular bungee replacements.  It was a fairly easy retrofit since the Jabiru is a light engine and there is plenty of working room between the engine and firewall.  I understand Zenith is going to make this system standard with new kits.

John

N750A

(Disclaimer: No business or financial affiliation with Zenith Aircraft.)

Views: 16971

Reply to This

Replies to This Discussion

Wow, you have a beautiful spot there.  

Rusty;
The plane was a total write off: on its back with a bent empennage, folded prop, bent wings, the works. I touched down firmly in a suddenly shifting 15 knot direct crosswind, bounced a bit, and as I added power to stabilize to either go around or touch down found that I had no rudder control at all. Rather than risking a spin or hitting the trees I elected to set it back down. When I lowered the nose, it kept right on dropping. The Front gear was completely retracted against that wire ring stop that is on the strut. That caused 2 things to happen: 1 - it jammed the nose gear steering and rudder control, 2 - when I placed the nose wheel the second time it wasn't "where it should have been" and hit with more and totally undampened impact.

With no rudder and no idea of why no rudder I decided to take my chances on the ground. That is what insurance is for; for bent airplanes not dead pilot's relatives benefits. But it happens fast and you don't have much time to make a decision.


By then I was off to the side of the grass field where the sod was soft from recent rains and because of no rudder and stiff cross wind I was not aligned in direction of travel. Impact plus soft earth plus side load folded the front gear. I used full backpressure to keep the nose as light as possible and flaperon to keep the wing out of the dirt. It slide on the nose about 100 feet. With loss of elevator effectiveness the plate mounted on the gear fork to accept a Piper tow bar, acted like a plow share and started digging a furrow. after about 25-30 feet of slide it had dug deep enough to catch and flip the plan on its back. It slid barely a foot after flipping, but with the rudder stuck in the soft dirt it caught and bent up everything.

The robust structure prevented any injuries. The forensics on the failed bungee showed localized embrittlement of about 75% of the fibers directly under the manufacturer's glued on tag, with no damage adjacent to the tag. The remaining fibers let go on the first bouncy landing. I highly suspect the use of an incompatible glue on the tag. The bungee was barely 2 years old and was inspected only 30 days prior.


Of course the FAA totally ignored the failure analysis, called it pilot error and lifted my license until I did remedial crosswind training and retook the my commercial check ride. It was an expensive, hostile, and humiliating experience. I didn't learn anything new about crosswind landings, but I did learn that the FAA has a quota of pilot scalps to fill and they are remorseless in trying to fill it. You don't want to be on their gotcha' list.


I am using a higher rated bungee which makes the steering and spring action very stiff. You can understand why I want to get rid of the bungee. I got a note from Zenith that they would look into donut conversion of an 801, but despite several emails and a call to them I have had zero response.


All I want to know is who makes the donuts? I can engineer the installation and make the rest of the parts myself, but can't find a source for the donuts. Are there any manufacturer identification markings on the donuts that come with the kit?

My kit showed up a couple days ago. I see no identification on the donuts.

Ditto - no i.d. marks or numbers on mine.

John

Hi John,

Just wondering if you received installation instructions with your puck install system.  My kit arrive with a detailed drawing but no written directions.

  James

James,

I believe John is out of the country on vacation until 02/20, so his reply may be delayed. John's 3rd paragraph above says he received step by step instructions. I would call Zenith and ask them to fax or email the instructions.

Jim

James,

As of a month ago there were no installation instructions.  I called and talked to Katlin.  She said to call and talk to Roger .  I never did.  The only question I had was the “pre-load” that John mentioned in this post.  With normal weight on the nose, I think you want the rudder attach tube to ride just above the bearing.  Then when in the air, they will ride on the bearing and self center.

     If you call Roger and get a different or better answer, please let us know 

Jeff

I wonder how the manufacturer can manage their quality process without a means of lot or batch identification?

An instruction sheet was included with my kit - Roger should be able to get you one. However, the drawing is pretty self-explanatory. I'd post my kit instructions except I'm out of the country for 2 more weeks. My first post basically follows the instructions step by step.
John

Could any of you please tell me how to get in contact with this Roger person who seems to have all of the answers. I haven't a clue who he is or how I can contact him by phone or mail. 

Thanks!

Stat at Zenith in Mexico, MO.  Don’t know number but sure it is on web site.  Ask anyone who answer to speak to Roger.

Roger works at the Zenith factory.  Call Zenith and ask for Roger:  573-581-9000 Monday to Friday 7 AM - 5 PM Central

I ordered a donut kit for my 801.  I received it, but have not installed it yet.

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service