Hi guys

Im working on my rib form blocks and I see others have what looks like cone shaped recesses for the flutes shaped into the form block. What's the tool you use to make those?

Is it a drum type bit you put on a drill press?

And the radius for the edge. Do you just sand it round by eye or do you use a proper router bit to put the 1/8 radius there?


Michael in Toronto

Views: 334

Reply to This

Replies to This Discussion

Hi MIchael,

Have you purchased the homebuilt help videos? The videos at

http://homebuilthelp.com/ZAC/Scratch_zac.htm

http://homebuilthelp.com/ZAC/metalpage101_Zenith.htm

can answer all those questions to get you started. Personally, I have purchased every video for every part of the construction of my 650.

You can also search around on youtube for hints as well, but for a very reasonable price the above videos can

get you off to a great start in scratchbuilding.

I use a radius router bit for the radius on the edge. My procedure for making form blocks is to cut and sand the outer surfaces to 90 degrees, then put the radius on the corner of the block, after that I bevel the outer edge to accomidate the springback. (radius the edge before cutting the angle or your formblock will end up undersized). then I cut the flutes. To bevel the angle and cut the flutes I use a rigid belt/drum sander from home depot, but your flutes could be cut on a drill press with the table tilted. All of these operations could be done by careful hand work it just takes longer. Dan 701 sn6856

great tip about doing the radius 1st.

I do own both the homebuilt videos the other gentleman mentioned but I was wondering about the sander as I have a disk sander but not the drum type as shown in the videos and was wondering if there was another way to do the flutes.

I do have a drill press but its the smaller type with a fixed table that moves up and down but not angled. I could work out and angle jig to hold it steady against a drum bit.

I appreciate the response as sometimes methods change over the years and its good to see I`m on the right path

In the videos they use a router table to do the radius, is it just as acceptable to do the radius with a handheld router and the rib screwed to the work table. I was wondering if a router table is a necessary item to get?

do you get more chips flying around from routering aluminum with the router table or if I routered with a hand held router and the rib jig screwed to the table would this be minimized? or either way I`m going to get covered?..lol

Thanks

Michael in Toronto

handheld will work but router table is easier and probably safer for the smaller pieces. I use a router table I built a long time ago and it works great. There is video of it in use in some of my u-tube videos on building access panels, you will wear lots of alluminum chips either way. Dan.

For the flutes, you could try a 1/2 inch wood rasp. I have one and have used it for tuning flute depths when I did not want to drag out the sander. I have not used the rasp to do flutes from scratch, but it should work.

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service