Hey guys/gals.  I am getting back into build mode and have some questions.  I want to make my main gear myself and would like to hear from you as to how you are bending the .75 6061 aluminum.  I have the press and all that I need to do it , just want to see how you do it.  Any special jigs or fixtures. 

Views: 578

Reply to This

Replies to This Discussion

okay then.

when i did mine i was concerned about heat treating i had read about , so i phoned the factory and they said they do it with out heat treating , i laid out the positions of radii on flat bar (fine tip felt marker) . fastend 3" round stock to  ram . marked 6 oclock on round stock . lined up marks and pressed into large v block . i made plywood angles to check bends . i know it seems a bit crude but when i was done i set the gear on level floor and put the level on top and it was level , i'm sure i got lucky . you might use a dial indicator between ram and bed to get angels (i mean angles although angels might be more appropriate since they fly and flying is good ... a little levity there and levity is good . i got to get out of these brackets) correct . any worry i had about the gear being strong enough went away when i watched a video on this sight . a large fellow demonstrating short landing came down real fast , pilot side wing real low and absolutely pancaked pilot side gear . it stood up fine

Thanks for the reply.  I kinda figured it would be simple. 

Jesse,

I was going to try to make my own main gear also. I was looking at the price of the aluminum and figured that I would have to try it twice at least to get it strait ant true. I had seen the price of the GROVE gear for My Kitfox (@ $2500.00) and figured I could do it for less. Then I looked on the Zenair site and the price was $580.00 and that is strait and true.

I ended up buying mine from Zenair. Guess I'm not a complete scratch builder, but now I know my tires wont wear out on the first taxi test. Buy the way the gear leg is marked 6061 T6 so yes it is heat treated.

Good luck and please post some pictures.

Paul

i believe a gear manufacturer starts with 6061-t6 aneals it , forms it , and rehardens it .

I work for Kaiser Aluminum and can tell you that the heat treat proses to get 6061 to a T6 condition is heat to 1000 deg. F @ 2 hrs quick quench with water, stretch 3 to 5 percent that gets it to a T4 and aligns the grains, then artificial age for @ 10 to 20 hrs. 

The best way to make the gear is just to bend it in the T6 condition that its in (like we do all the rest of the metal on the 750) not a problem if you have a hydraulic press.  I made my nose gear fork that way out of 2024 T3 (much harder metal) and it turned out fine.

Well that my 1/2 cent worth, again good luck and keep on building.

Paul

Jesse - Bend the T6 cold and you must have proper grain direction. Also the radius is 3" therefore you need something 6" in diameter to do the bending.

Im gonna bend it in its natural form.  I can buy the aluinum for 158.00 so I can mess up 3 times and still be ahead of the game.  Thanks for all of the ideas and replys.

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service