Just wondering if anyone has used something other than the nylon block fairlead - like a pulley.  Seems to me that a steel cable rubbing against a piece of plastic is prone to cable tension changes as wear occurs?

Views: 2012

Reply to This

Replies to This Discussion

I have wondered the same thing. However, a lot of Zeniths have flown a lot of years with the plastic block fairleads and not had problems. I will most likely stick with the plans - simple, effective, weighs less. I await input from those who have been flying as to the longevity and reliability of the stock fairleads.

Brian,

 

Since no one has yet responded about using pulleys, I guess I am going to chime in like Bob did and say the current design is working for me.  4 years, 221+ hours and over 500 landings and I do not have any real nylon fairlead wear to speak of.  Regardless, I check the cable tension by feel prior to every day's flying and with a tension gauge at every oil change.  To date I have never had to re-tension anything in my control system due solely to operational wear.  Since nylon fairleads are only meant for light angles, 7 degrees or less, if I recall, they should not be under a huge wear load. For now I would recommed sticking to the plans.

 

Good luck,

 

Dave

Thanks Bob and Dave!

That's all I need to know, it sounds like it is a complete non-issue and I don't need to waste time thinking or worrying about it.  I was more curious than anything, since I am a complete aircraft newbie.  I've been surfing a lot of different builder sites and other resources, and see a lot of talk about phenolic pulleys, etc. - those are probably meant for much more radical shifts in cable direction.

Brian M.

I will be making up pulley frames and having pulleise where possable. Wires rubbing on plastic is not for me nor is it ok for Cessna or Piper.   I am building a Ch650B.  I will not be doing any cable fairlead work untill finished fus it needed.

Nearly 300 hrs on a 750 and so far I can't detect any wear on the fairleads - controls are nice and smooth!

John

N750A

I've seen a pulley put in the top rear fuselage for the elevator upper cable.  If there was one that was needed it would be there!  I just tensioned up my cables and I don't like the feel of that cable rubbing on anything so I wish I would have put one there.  :(   There was a picture here somewhere of somebody who thought the same and put a pulley in that spot...

Besides that I don't think they would be needed anywhere else, and like everyone else has stated there haven't been any issues that have come up!

I agree, look at how many nylon fairleads a Piper J3 Cub has just on the struts. They've had 65+ years to determine if wear was an issue, so I'm comfortable with that test period. Simple and light.

Walt Snyder

Yeah, that question was posted a LONG time ago... long before I actually had things built, and it was based on conjecture and not experience. My controls are silky smooth with the original designed fairleads. I did opt for the Viking "steel bungee" however. The only real issue I had was the stiffness of the rudder and now that is also a non-issue.

I ended up using the oil fill nylon for the rudder and elevator  cables.     For the wings i used push pull rod, so no wires.

My take is that even if you are using a pulley to guide the direction of the cables they are in many instances passing thru a relativly small hole in the aluminum skin and would be at least intermittently contacting the aluminum. the nylon fairleads will prevent that and protect the aluminum and the cable.

I went all through this with the A&P that did my conditional. I even went so for as fabricating pulley's for my elevator cables until  my local DAR set them straight. I did make some new fairleads out of 1/4" oil filled nylon from McMaster carr that made everyone happy,, but wasn't really required or needed

I had an IA look at my rudder cables and he recommended using a plastic bushing at the front fairlead hole. Instead I used a 1ft length of brake line over the cable. This slides thru the hole very smoothly and hopefully solves any future problems. 

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service