Joe Hopwood's Comments

Comment Wall (11 comments)

You need to be a member of Zenith Aircraft Builders and Flyers to add comments!

Join Zenith Aircraft Builders and Flyers

At 2:27pm on September 11, 2023, John Austin said…

Hi Joe,

I don't know why you don't receive notifications - Efe Cem Elci, one of our members, is very computer savvy and might be able to help you out.

John

At 5:30am on June 18, 2021, Michael Mccarthy said…

Hello,

My name is Mr. Michael Mccarthy, I have contacted you before without any response from you. Please replied if you receive this message. I have something very important to discuss with you, I have a vital information to give you. Could you please get back to me on (mmichaelmccarthy4@gmail.com ) for full details.

Michael Mccarthy.

At 8:17am on September 1, 2016, Evan Reisman said…

Thanks Joe. I went ahead and ordered a new steering rod from Zenith. It was only $16 and change with the various hardware. Once I have it off, I'll post a picture. Basically, the bent steering rod made it so that the left and right rudder pedals weren't even when the plane was taxiing straight. This would make for a tricky landing, especially if side slipping, so I decided to just replace the part.

At 8:21am on May 10, 2015, Don Woodward said…

Hi Joe

I have done Zenith paper transferr work for my Ch650B now  so hope to get updates soon.

At 11:10am on June 29, 2013, Jim Snyder said…

Joe,

 

Reading your Kitlog section re: canopy hoop problems.  I have exactly the same problems.  I have been wrestling with this for 3 months.  This &^%$#@! thing is making me suicidal.  How did you finally resolve yours? 

 

Jim Snyder

Indianapolis

At 4:49pm on September 4, 2011, John Benton said…
Joe: I did run both cables through the firewall. The knob ends are located just under the panel at the extreme left and right sides of the cockpit. The carburetor ends terminate in Heim bearings that are bolted with a long AN bolt and spacer to the throttle arm. I am considering making a change to bolt each bearing to a separate hole to get rid of the long bolt, but this would change the "throw" length of one of the cables, so this change is still in the "thinking about it" stege. I do understand your desire to keep the firewall with as few holes as possible.
At 2:39pm on September 4, 2011, John Benton said…
Joe: Since my engine is a Continental, I was concerned only with the throttle. I believe that the mixture located in the center would be no problem and of course I have no choke. I ran two flexible cables salvaged from a Cessna with an extended attach point on the carburetor throttle arm. The pilot's side cable can be locked for cruise stability, but I removed the locking feature from the co-pilots side. The plane has not yet flown, but the system works easily and well.
At 9:36am on January 28, 2011, Don Davis said…
Looks like you are about in the same position I was a year or two ago when the rebuild order came down.  I was asking questions about the Dynon autopilot installation and working on my canopy.  I haven't finished any of those things.  And just getting started on my rebuild.  But I am getting fired back up again.  Got one wing out of the rack and removed the top and nose skins yesterday.  Going out to start on the main spar reinforcement today.  My big question is, should I bother with primer paint on these parts, or just hurry up and install them bare, no paint.  All my other parts are primed on the contact surfaces.
At 11:57pm on January 13, 2011, David Gallagher said…
Joe, The positioning should not pose any elevator travel issues. You can experiment by clecoing the the attach pieces to the fuselage and fitting the HS with clamps. Put the HS full forward and then as far a ft as edge spacing will allow and see if there are any elevator travel problems with either placement.
At 3:34pm on January 13, 2011, David Gallagher said…

Joe, I tried to reply to your forum question, but it would not let me post it..issues with my laptop combined with being on an overseas business trip, I suspect.  I will try to leave it to you directly on your comment wall-------->

 

Just my opinion of the Zenith design tennants combined with over simplified logic skils (with some humor mixed in):

HS fore and aft positioning is defined by:  A+B+C=D

As:

A=The HS cannot be mounted any further forward that that aft fuselage bulkhead.

B=The HS cannot be mounted much more that an inch or so aft of that bulkhead with out starting to violate the edge distances on the HS attach pieces

C=Chris Heintz says aint rocket science.

Thus D=put it somehwere between the two points and you will be OK.

 

Personally I placed it just a hairs distance behind the aft bulkhead.

 

Good luck,

 

Dave Gallagher (camped out 3000 miles from my airplane so I can't fly)

 

P.S. I had to drop my HS leading edge down a handful of degrees to get my elevator trim forces where I liked them.

At 4:35pm on July 15, 2009, Tim Egan said…
Hi Joe,
I removed my question, I found the answer.
TImE

New from Zenith:

Zenith Planes For Sale 
  

Classified listing for buying or selling your Zenith building or flying related stuff...

Custom Instrument Panels
for your Zenith:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.

Zenith Homecoming Tee:

Zenair Floats

Flying On Your Own Wings:
 A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service