Online Community of Zenith Builders and Flyers
Press Release: October 2019
Lionheart Creations Ltd.
Lionheart Creations Ltd. has released the…Continue
Added by Zenith Aero on October 10, 2019 at 11:00am — No Comments
Hope to solve soon but do any of my fellow builders have experience in the total resistor value needed to solve erratic rpm readings on Dynon HDX unit and Continental O -200? Tried 30k, 62k, 92k, off p lead and the display still goes bonkers at rpm exceeding 2300. Thanks in advance.
I saw a post a few days ago about 3d printed fairings for the cruzer, but cant find that post or the link to download to make the fairings.
any one has that info and could repost?
Added by Mickey R. Mathieson on October 1, 2019 at 12:00am — No Comments
Added by Mickey R. Mathieson on September 26, 2019 at 7:20pm — No Comments
This was my second year to participate in our local county's DART exercise. I flew three missions during our mock exercise last weekend. We deliver food to food banks in the area using donated food as our load for practice. All loads were weighed and loaded in general aviation aircraft at the pilots direction. I flew 100 lbs on one trip and 75 lbs the second. Took pics of all the bridges on my recon flight. The STOL CH 701 is perfect for this. This really is a good program and it enhances…Continue
I have spent a little time experimenting with rudder trim, and I think it would be worthwhile to share my experiences with the group. I know that most of you are probably saying "Why?" to the concept of rudder trim for our STOL aircraft. In most cases, it is probably not necessary. However, I found it useful. I'll explain.....
The Aerosport IO-375 makes 195 hp, and lots of P-factor. With that power plant, one can point the nose up and go. In the 801, I can also haul a…Continue
I recently purchased a Bosch GSC 12V-13 Cordless Sheet Metal Shear. After having a chance to use it a little bit, I decided to post a demonstration of its use online.
My short assessment is that the shear will have its uses, but because of the stretching caused by the shearing action it would not be suitable for cutting parts that need to remain as flat as possible.…Continue
Added by Damon Brantley on September 22, 2019 at 11:46am — No Comments
Added by Bradford Drown on September 11, 2019 at 8:25pm — No Comments
Dear collegues, I am in the final building process and cannot locate instructions-guide on how to measure-cut - place - secure top window.
Would apprecciate any input on where this info is??
Thank you all
Added by Jonathan Kennedy on September 11, 2019 at 8:24pm — No Comments
An issue with the center wing spar rib stations presented when fitting the rear ribs. The spar rivet holes are pre-drilled and the flange on the rear rib is not. I noticed that the top and bottom spar web rivet positions were very close to the ends of the rear rib flange, violating the 3 diameter minimum 2 diameter rule for rivets. I spoke with Roger at the factory. and the top and bottom rivets are useless. As a solution, another rivet hole is added at the top and bottom of the rib station…Continue
Earl Downs is a Zenith builder who is known to many others builders because he furnishes pre-test flight preparation training in his 601 XL-B. Because he holds an FAA Letter of Deviation Authorization (LODA), Earl is allowed to provide this and transition training for both the 601 and the 650. You may also have met Earl as a forum presenter at a previous Zenith Aircraft open house events.…Continue
Added by Zenith Aero on September 11, 2019 at 11:00am — No Comments
Scratch construction of the ailerons and flaps has been started. I decided to try to document as much of the construction of these as possible as this should be my last major set of parts to bend. There will be two or three parts to this. In the first part, I document the construction of test sections to verify my CAD drawings are correct.…Continue
Added by Damon Brantley on September 9, 2019 at 7:18am — No Comments
Added by Bradford Drown on September 6, 2019 at 4:45pm — No Comments
No easy task. After a lot of study of the drawings, I totally screwed up the first two gear channel parts and ordered new ones. I believe I have the left one done; drilled, clecoed and ready to rivet. I will to wait on the spar riveting, I see some challenges there with the second row of rivets in the rib channels. …Continue
Added by Bradford Drown on August 30, 2019 at 4:00pm — No Comments