Online Community of Zenith Builders and Flyers
Since the Air in the Hawaiian islands contains high contents of salt and sulfur dioxide I decided to cortec the inside skins as well as a complete skeleton.
Added by Mickey R. Mathieson on June 26, 2019 at 1:02am — No Comments
Completed the Rudder on Saturday, June 22nd. A good learning experience. I had to remove my first bad rivet due to a gap at the head. Sweated that out since it was one of the last rivets installed prior to completion. However, it went well and no damage to the skin. It was on the nose rib, forward skin so I didn't have to chase the rivet inside the rudder. Viewed the online video of the rudder build at the factory and I understand now why this kit will be a bit…Continue
Added by dschmaz on June 20, 2019 at 6:30am — No Comments
Quality Sport Planes (QSP) is hosting its annual Open House and Fly-In and retirement party for Doug Dugger on Saturday, June 22, from 10 am - 4 pm, at the QSP facilities at Cloverdale Municipal Airport (O60) in California:…Continue
I did a quick project update video for those who've been asking: https://evadot.com/2019/06/17/cruzer-update-video/
Added by dschmaz on June 17, 2019 at 9:06am — No Comments
Painted Cabin. Now Final Assembly can start
Added by dschmaz on June 17, 2019 at 9:04am — No Comments
Added by Jim and Amelia Isaacs on June 9, 2019 at 6:01pm — No Comments
Added by Jim and Amelia Isaacs on June 9, 2019 at 6:00pm — No Comments
Flat gasket for Gascolator A10580-T
Brake pads for a Grove 30-1 caliper
Soft filter for carburetor intake on a Lycoming O-235
Added by Dick Miles on June 7, 2019 at 9:57am — No Comments
The crate arrived today after a couple of adventures. Zenith shipped on May 24th and shortly thereafter the weather turned horrible. I got a notice of a 'weather delay' on my crate and waited to hear if it went flying without me. However, it arrived in NH on 06/01, and my house on 6/04. The second worry was the forklift puncture at the water line of the crate. (See photo). The fork did travel into the crate however, the only damage was a destroyed corner of the packing list envelope…Continue
My Cleco cans are filling back up as I rivet skins
Cruzer circuit practice with full flap landings, plus coastal scenery flight; Fleureiu Peninsula, South Australia, at 8x speed, no music - 8 min/fast video. Last landing with half flaps and side slipped. Camera beneath the plane. For fellow Builders - keep going - a very forgiving plane, not fast.
Added by John Sanders on May 17, 2019 at 9:23pm — No Comments
One thing that has often been a problem is trying to keep parts from getting lost as they wait to be added to larger assemblies. While I am scatchbuilding, the problem is no doubt worse for someone building from a kit because they get all their parts at once.
Something that has recently been quite useful for me is to use mini-stretch wrap.…Continue
Added by Damon Brantley on May 11, 2019 at 9:00pm — No Comments
The April 2019 issue of AgAir Update, the monthly magazine for the agricultural aviation (crop spraying) industry, reprinted a flight evaluation article of the STOL CH 701 "Sky Jeep" light sport aircraft (first published twenty years…Continue
Added by Zenith Aero on May 10, 2019 at 3:30pm — No Comments
Hi All, 9 min YouTube - new kitbuilt 750 Cruzer with a Viking engine.
Scenic lap of Hindmarsh Island, South Australia - best on a big screen.
At 6 minutes you can jump fwd to the end, for the landing, if you wish.
All clips sped up 200%, audio down to 20%, no music.
Now at 16 hours, all systems good, lots of power, leaps off the ground.
Latest is various…
A panel hacksaw is a special type of saw for making long cuts in pieces of sheet metal. By using a piece of spring steel sheet to support the blade allows the saw to make unrestricted cuts.
A demonstration is made of trimming down a wing skin.