Leo Arrigo
  • Male
  • Fort Frances, Ontario
  • Canada
Share on Facebook
Share

Leo Arrigo's Friends

  • Bashar Hussien
  • Martin Bima
  • Kevin Boelk
  • Daniel
  • Greg Ross
  • Conrad Watters
  • J. Davis
  • Ari Hulkkonen
  • Paul Sanders
  • Joseph F. Truncale
  • Clay E Hollenback
  • Andre Levesque
  • giuseppe lomonaco
  • Conrad Watters
  • Mark Thomas

Leo Arrigo's Discussions

75F-4-1 Side Channel CH750

Started this discussion. Last reply by Leo Arrigo Mar 29, 2011. 4 Replies

I am joining the fuselage today and I have not completed the Side Channel. Does anyone know where to find the working instructions(picture assy) as to what needs to be drilled out. I know there is…Continue

 

Leo Arrigo's Page

Profile Information

Aircraft Model
STOL CH 750
Project Status
Just started
Building From
Kit
Building Experience
No Experience
Flying Experience
Private Pilot

Leo Arrigo's Photos

  • Add Photos
  • View All

Leo Arrigo's Videos

  • Add Videos
  • View All

Leo Arrigo's Blog

Arm Rest Interference

Posted on May 1, 2011 at 12:50pm 3 Comments

 

Is anyone having issues with the back of the armrest sides being approx 10mm higher the the tunnel top panel when installed.

 

This problem has been dogging me since joining the rear and front fuselage. All other parts and pieces seem to line up just fine.

 

 

Any help or comments would be greatly appreciated.

 

 

Leo

Comment Wall (13 comments)

You need to be a member of Zenith Aircraft Builders and Flyers to add comments!

Join Zenith Aircraft Builders and Flyers

At 10:49pm on October 28, 2011, Kevin Boelk said…
I saw a picture of Conrad Watters 750.  It looks pretty good.
At 9:01pm on October 6, 2011, Fred Stratman said…

Thanks for the reply Leo.  It looks like we are both right and the Homebuilt Help video that I used as a guide has it wrong.

Now I can work on replacing clecos with rivets before the snow flies here in Iowa.

Best Wishes ...  Fred

At 11:07am on October 6, 2011, Fred Stratman said…
I meant "drawback to having the gear channel flange outside of the fuselage"
At 9:55am on October 6, 2011, Fred Stratman said…

Hi Leo

How did you fix the "arm rest interference" problem? 

I had the same situation and fixed it by clecoing the aft flange of the gear channel under the rear fuse instead of inside.  That brought the rear of the arm rest sides down to fit perfectly.  And I didn't need to use brute force to place the seat bases between the rear seat channels and the lower baggage floor.

Now I am trying to determine if there is any downside to having the gear channel flange inside the fuselage so I can start drilling out and riveting.

I will appreciate any information.

At 9:08pm on June 20, 2011, Mark Thomas said…
Added a discussion about the Jabiru that might answer some of your questions about it.  Feel free to contact me for any add'l info.
At 10:32am on March 6, 2011, Mike Ice said…

Leo,

Deburring is important but check out this tool, it may make the process much easier: http://www.yardstore.com/browse.cfm?viewfrom=13&catid=334&step=2

The tool deburrs both sides of the hole at once.

Mike Ice

At 7:31pm on March 31, 2010, Joseph F. Truncale said…
Ditto Leo on the Demo ride on that Friday for me. Most impressive was the stall characteristic - flat and gentle - I wouldn't have know if he didn't tell me we were going down (pays to watch the altimeter).
I finished inventory last nite and have all the parts in separate kits...finally.
Joe
At 5:06pm on March 30, 2010, Conrad Watters said…
Leo ,
The stretch through North west Ontario looks like it will need a way point at Fort Francis --for sure.
So far I have flown with Angus in his 750 for 3+ hours.It is very responsive and feels particularly solid ---for a fellow who has enjoyed flying Challengers for the last 10 yrs.
Conrad
no doubt you have seen Angus' pirep
At 8:13am on March 30, 2010, Robert Pelland said…
Leo,

I only prime the mating surfaces
Robert
At 8:40pm on March 29, 2010, Conrad Watters said…
Leo I do not see my reply re: corrosion protection.
Yes I will be covering any and all exposed metal. My plan is to be on floats in fresh water. Ultimately I would like to fly to all coasts --east, west and perhaps north, if I can manage it. Conrad
 
 
 

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...

                                                     

Weather Maps


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, power distribution panel, Approach Fast Stack harnesses, Dynon and Garmin avionics, and more.


Custom Upholstery Kits for your Zenith Aircraft:

Zenith Vinyl Upholstery Kits


Zenith Apparel from EAA:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

Aircraft Insurance:

 
 

West Coast USA:

Transition Training:

Pro Builder Assistance
 

Pro Builder Assistance

Aircraft Spruce & Specialty for all your building and pilot supplies!

© 2019   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service