Workbench height - Zenith Aircraft Builders and Flyers2024-03-29T07:06:39Zhttps://zenith.aero/forum/topics/workbench-height?commentId=2606393%3AComment%3A345186&feed=yes&xn_auth=noBrendon,
Here's a good way t…tag:zenith.aero,2014-03-16:2606393:Comment:3456072014-03-16T04:56:13.217ZWalt Snyderhttps://zenith.aero/profile/WaltSnyder189
<p>Brendon, </p>
<p>Here's a good way that us guys in the States use at times to determine workbench height. Go to your kitchen and do about two sink loads of dishes for your wife, and check out the pain you get in your back from being hunched over doing those dishes. Check out the height of your counter, and after telling yourself and your wife you'll never of that again, figure out how much you need to add to that counter height to stand there doing that again. </p>
<p></p>
<p>For me, it…</p>
<p>Brendon, </p>
<p>Here's a good way that us guys in the States use at times to determine workbench height. Go to your kitchen and do about two sink loads of dishes for your wife, and check out the pain you get in your back from being hunched over doing those dishes. Check out the height of your counter, and after telling yourself and your wife you'll never of that again, figure out how much you need to add to that counter height to stand there doing that again. </p>
<p></p>
<p>For me, it was 37 inches, and I'm 6-2. And unfortunately, I still do the dishes…….sometimes…...</p>
<p></p>
<p>Walt Snyder</p>
<p>N10ZE</p> I'm 5' 8" and was thinking I'…tag:zenith.aero,2014-03-16:2606393:Comment:3457582014-03-16T03:37:34.215ZDaniel C Hallhttps://zenith.aero/profile/DanielCHall
<p>I'm 5' 8" and was thinking I'd go with 36" or even 37" but maybe I should re-think that. It's not so much my back as my shoulders and neck that aggravate me. I don't want to have my head down all day. We'll see. </p>
<p></p>
<p>Dan</p>
<p>I'm 5' 8" and was thinking I'd go with 36" or even 37" but maybe I should re-think that. It's not so much my back as my shoulders and neck that aggravate me. I don't want to have my head down all day. We'll see. </p>
<p></p>
<p>Dan</p> Thanks for the info,
33" wil…tag:zenith.aero,2014-03-14:2606393:Comment:3450462014-03-14T12:53:34.295ZBrendon Tadgellhttps://zenith.aero/profile/BrendonTadgell
<p>Thanks for the info,</p>
<p></p>
<p>33" will do the job, I will have adjustable feet so will have +/- 1.5".</p>
<p></p>
<p>The plan has always been to have two 4'x6' benches that can be connected flat and level.</p>
<p></p>
<p>Thanks for the responses, It's good to get some feedback and hopefully save my back!</p>
<p></p>
<p>I'll post some pics when its all built.</p>
<p></p>
<p>Kind Regards,</p>
<p>Brendon Tadgell</p>
<p>CH-701</p>
<p>Thanks for the info,</p>
<p></p>
<p>33" will do the job, I will have adjustable feet so will have +/- 1.5".</p>
<p></p>
<p>The plan has always been to have two 4'x6' benches that can be connected flat and level.</p>
<p></p>
<p>Thanks for the responses, It's good to get some feedback and hopefully save my back!</p>
<p></p>
<p>I'll post some pics when its all built.</p>
<p></p>
<p>Kind Regards,</p>
<p>Brendon Tadgell</p>
<p>CH-701</p> Another tip:
I made my primar…tag:zenith.aero,2014-03-14:2606393:Comment:3453202014-03-14T12:46:47.519ZJohn Austinhttps://zenith.aero/profile/JohnLAustin
<p>Another tip:</p>
<p>I made my primary work table 4'x10' (and 34" as I recall). I built a secondary work table 4'x4' on a dolly with casters and made sure the overall height was exactly the same as the primary table. Then, when working on oversize pieces like the rear fuselage skins, I'd put the two tables together so I'd have 14'. Later, when the fuselage was on the gear and not so easily maneuverable, I found having the smaller rolling table was very handy - I could push it over near the…</p>
<p>Another tip:</p>
<p>I made my primary work table 4'x10' (and 34" as I recall). I built a secondary work table 4'x4' on a dolly with casters and made sure the overall height was exactly the same as the primary table. Then, when working on oversize pieces like the rear fuselage skins, I'd put the two tables together so I'd have 14'. Later, when the fuselage was on the gear and not so easily maneuverable, I found having the smaller rolling table was very handy - I could push it over near the fuselage and keep parts, tools, etc. close by. Also, the dolly had a solid surface so the 4'x4' shelf was great for storage of frequently used materials.</p>
<p>John</p>
<p>N750A</p> Brendon - I'm your height and…tag:zenith.aero,2014-03-13:2606393:Comment:3451862014-03-13T12:45:52.518ZChris Aysenhttps://zenith.aero/profile/ChrisAysen
<p>Brendon - I'm your height and I find a 34" high table feels like the right level. My arms are bent and not pulling on my lower back when they are in front of me. I believe you could go as low as 32" but no lower than that. Your arms are quite heavy and when extended in front of you for long periods of time put considerable pressure on your lower back. Least that was my experience. I'm not a orthopedic surgeon or phyiscal therapist.</p>
<p>Chris</p>
<p>Brendon - I'm your height and I find a 34" high table feels like the right level. My arms are bent and not pulling on my lower back when they are in front of me. I believe you could go as low as 32" but no lower than that. Your arms are quite heavy and when extended in front of you for long periods of time put considerable pressure on your lower back. Least that was my experience. I'm not a orthopedic surgeon or phyiscal therapist.</p>
<p>Chris</p> I would say whatever feels go…tag:zenith.aero,2014-03-13:2606393:Comment:3450052014-03-13T11:12:13.885ZJesse Hartmanhttps://zenith.aero/profile/JesseHartman
<p>I would say whatever feels good to you. You want it high enough that your not bent way over.</p>
<p>I would say whatever feels good to you. You want it high enough that your not bent way over.</p>