Hello,

I posted this on the jabcamit forum, but thought I'd post here too, just in case...

I'm installing a 4th gen 3300 on a CH601-HD.
Question regarding throttle cable: in my case, the cable end is interfering with the idle screw.
Is this normal? I suppose I should (?) adjust the cable length, so its end won't touch the screw, but the installation manual does not touch the subject.
I might be able to fix this by adding washers, so the hole for the cotter pin is closer to the throttle arm, but I wonder if there is a better solution.
(photo attached)
Thanks in advance for your comments
Carlos Sa

Views: 77

Attachments:

Reply to This

Replies to This Discussion

Do you have a throttle extension arm on the Bing? That should give you the clearance and provide a longer throttle throw, making finer throttle adjustments easier. You can get one from Arion Aircraft.

John

N750A

Hello, John

No, I don't have the extension, but it did cross my mind.

However, I suspect the geometry of my installation would not allow for full throttle travel.

But I'll take a closer look.

Thanks for the suggestion.

Cheers

Carlos

I have a Gen 4 on a STOL CH750 and with the throttle extension (from the Arion Aircraft Firewall Forward Package) it does not interfere and the throttle has normal travel for an aircraft throttle.  You will however need an additional idle stop.  The extra leverage is too much for the idle tab on the carburetor.  NAPA has cable stops that will do the trick.  You just need one set on the cable so the stop hits the cable jacket at idle speed.

Thanks for the comments, John

I looked at my setup: the throttle travel (in the cockpit) is 10 cm / 4", while on the carb it is 1.25".

Here's a picture of the rod w/ levers: http://www.zenith.aero/photo/throttle-installation-1?context=user

(The pilot's control can be seen on the top left of the photo).

In conclusion, I don't think I can use the arm extension approach. Adding washers seems to be the best approach, so far.

I don't see what dual throttles has to do with it. Doesn't the extension go on the carb where there's only one cable?

And yes, you can use extra washers.

As it is, the throttle knob (in the cockpit) has a travel of ~3", while at the carb, the throttle arm moves ~1".

If I were to install the arm extender, the throttle knob travel would change to over 6".

(But since the cross shaft can't rotate that much, the throttle travel would be reduced to 50%.)

In case you are not familiar with the dual throttle arrangement, below is a photo from a Jabiru aircraft manual (unfortunately I do not have a decent picture of my installation). The shaft and levers are identical to what I received.

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Custom Upholstery Kits for your Zenith Aircraft:

Zenith Vinyl Upholstery Kits


Zenith Apparel from EAA:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Golden Eagle Aviation

Pianosa Flying Farm

Aircraft Spruce & Specialty for all your building and pilot supplies!

© 2022   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service