Do AN 363 (Metal Locknuts) Affect Torque Values? - Zenith Aircraft Builders and Flyers2024-03-28T23:58:22Zhttps://zenith.aero/forum/topics/do-an-363-metal-locknuts-affect-torque-values?commentId=2606393%3AComment%3A172799&x=1&feed=yes&xn_auth=noI should add that Lock-Tite w…tag:zenith.aero,2011-11-07:2606393:Comment:1727992011-11-07T02:31:47.688ZBrian Fitzpatrickhttps://zenith.aero/profile/BrianFitzpatrick
<p>I should add that Lock-Tite will act like a lubricant when torquing so torque to lubed specs. Less torque.</p>
<p>Brian</p>
<p>I should add that Lock-Tite will act like a lubricant when torquing so torque to lubed specs. Less torque.</p>
<p>Brian</p> Torque wrenches are a great t…tag:zenith.aero,2011-11-07:2606393:Comment:1727972011-11-07T02:27:19.013ZBrian Fitzpatrickhttps://zenith.aero/profile/BrianFitzpatrick
<p>Torque wrenches are a great tool for getting consistent values but accurate calibration should not be taken for granted.</p>
<p>When I bolt things together my real peace of mind is Loct-Tite. Get the red stuff. The blue stuff doesn't hold like the red. Be careful not to get carried away on the smaller fasteners like AN-3 caps and nuts as the threads will often be damaged during dis-assembly.</p>
<p>Speaking of dis-assembly, warm up the nut to about 150 Farenheit with small propane torch on…</p>
<p>Torque wrenches are a great tool for getting consistent values but accurate calibration should not be taken for granted.</p>
<p>When I bolt things together my real peace of mind is Loct-Tite. Get the red stuff. The blue stuff doesn't hold like the red. Be careful not to get carried away on the smaller fasteners like AN-3 caps and nuts as the threads will often be damaged during dis-assembly.</p>
<p>Speaking of dis-assembly, warm up the nut to about 150 Farenheit with small propane torch on nuts to get easy release if necessary.</p>
<p>Brian</p>
<p> </p> Just FYI there is such a thin…tag:zenith.aero,2011-11-07:2606393:Comment:1728732011-11-07T02:01:19.033ZMichael Herderhttps://zenith.aero/profile/MichaelHerder
Just FYI there is such a thing as a castelated lock nut. I used theme where I really really didn't want to have to worry about whether or not I cotter pinned. i.e. control surfaces. Not that I would ever intentionally leave out a pin and count on it, but it just might save my bacon some day... for an -3 they are about a2 bucks a piece... Not cheap, but ehh...
Just FYI there is such a thing as a castelated lock nut. I used theme where I really really didn't want to have to worry about whether or not I cotter pinned. i.e. control surfaces. Not that I would ever intentionally leave out a pin and count on it, but it just might save my bacon some day... for an -3 they are about a2 bucks a piece... Not cheap, but ehh... I think using a castle nut on…tag:zenith.aero,2011-11-06:2606393:Comment:1726452011-11-06T14:54:50.620ZJohn Austinhttps://zenith.aero/profile/JohnLAustin
<p>I think using a castle nut on a motor mount <em>would</em> cause a lot of worry! LOL! I would think you need that mount defintely torqued-down so there is no possibility of motion where it meets the firewall which would result in fretting. I don't think castle nuts are intended to be used where there is a significant element of tension in the bolt - they are more or less just retainers for a bolt in shear on a rotating part like a control linkage.</p>
<p>John</p>
<p>I think using a castle nut on a motor mount <em>would</em> cause a lot of worry! LOL! I would think you need that mount defintely torqued-down so there is no possibility of motion where it meets the firewall which would result in fretting. I don't think castle nuts are intended to be used where there is a significant element of tension in the bolt - they are more or less just retainers for a bolt in shear on a rotating part like a control linkage.</p>
<p>John</p> It seems my concern about the…tag:zenith.aero,2011-11-06:2606393:Comment:1726602011-11-06T13:14:29.356ZJohn Austinhttps://zenith.aero/profile/JohnLAustin
<p>It seems my concern about the metal locknuts was "much ado about nothing"! It <em>seemed</em> to me that there was an awful lot of drag when using the metal locknuts, so that's why I was concerned about the torque values ... I think the engine mount is probably one of the places where proper torque <em>is</em> a good thing!</p>
<p>However, I found that although initially the drag is high, once you get the nut going on the threads, the drag drops off considerably. With AN 6 bolts, the drag…</p>
<p>It seems my concern about the metal locknuts was "much ado about nothing"! It <em>seemed</em> to me that there was an awful lot of drag when using the metal locknuts, so that's why I was concerned about the torque values ... I think the engine mount is probably one of the places where proper torque <em>is</em> a good thing!</p>
<p>However, I found that although initially the drag is high, once you get the nut going on the threads, the drag drops off considerably. With AN 6 bolts, the drag torque on the metal nut was only about 2 ft lbs. - Sooo, looks to me like just torquing to mid range gets you safely within specs.</p>
<p>Thanks,</p>
<p>John</p> Good question, normally in a…tag:zenith.aero,2011-11-06:2606393:Comment:1725052011-11-06T11:40:52.909ZJacobhttps://zenith.aero/profile/Jacob
Good question, normally in a situation more critical they will use a wet torque for say a crankcase, conrods, props this provides a more consistant torque or if they want to be more precise again they will have you measure bolt stretch some engine makers make you do this with conrods. I've never adjusted a torque value due to the nut used though, although you certainly won' t do any harm by going say an extra 5% on standard AN values if your concerned. Just use a bit of common sense and be…
Good question, normally in a situation more critical they will use a wet torque for say a crankcase, conrods, props this provides a more consistant torque or if they want to be more precise again they will have you measure bolt stretch some engine makers make you do this with conrods. I've never adjusted a torque value due to the nut used though, although you certainly won' t do any harm by going say an extra 5% on standard AN values if your concerned. Just use a bit of common sense and be consistant e.g. think about what your clamping, sometimes recomended torques are crap I find myself going a little higher in lots of senario's especially with smaller fasteners. Most people won't torque the majority of AN bolts installed on an aircraft unless specified by the manufacturer and I've seen plenty of people do up engine mounts without torquing them and they don't fall out although I'm not suggesting it though. Thanks to all for the good in…tag:zenith.aero,2011-10-31:2606393:Comment:1711962011-10-31T14:20:16.954ZJohn Austinhttps://zenith.aero/profile/JohnLAustin
<p>Thanks to all for the good info!</p>
<p>Caleb replied this a.m. that for the metal 363 nuts, use the 365 torque tables (as found in AC43.13-1B) for the bolts. He did not specifically mention, but as pointed out by others above, one would determine the drag torque of the nut and add that to the value.</p>
<p>Thanks again,</p>
<p>John</p>
<p>Thanks to all for the good info!</p>
<p>Caleb replied this a.m. that for the metal 363 nuts, use the 365 torque tables (as found in AC43.13-1B) for the bolts. He did not specifically mention, but as pointed out by others above, one would determine the drag torque of the nut and add that to the value.</p>
<p>Thanks again,</p>
<p>John</p> I have to assemble critical h…tag:zenith.aero,2011-10-31:2606393:Comment:1712942011-10-31T14:04:03.011ZRebecca Anne Shipmanhttps://zenith.aero/profile/RebeccaAnneShipman
I have to assemble critical high pressure extrusion dies for my job. We always torque the bolts to a specific value, and it makes a difference. Designers use these values to determine how many fasteners, how far apart, etc. The one thing that is new for me is the "drag torque", you get from locknuts. The construction standards say to add that on to the bolt torque when you are doing the bolt torque. With a beam wrench it's easy. I don't have one, so I turn down my "clicker" wrench as far…
I have to assemble critical high pressure extrusion dies for my job. We always torque the bolts to a specific value, and it makes a difference. Designers use these values to determine how many fasteners, how far apart, etc. The one thing that is new for me is the "drag torque", you get from locknuts. The construction standards say to add that on to the bolt torque when you are doing the bolt torque. With a beam wrench it's easy. I don't have one, so I turn down my "clicker" wrench as far as possible, and turn it up until I can turn the bolt loosely w/ no click. (so only the drag for the nut shows). Then I add this value to the bolt torque value to tighten. The construction standards show most of the raw bolt torque values. If torque values were not imp…tag:zenith.aero,2011-10-30:2606393:Comment:1712632011-10-30T21:22:30.219ZPhillip Owenshttps://zenith.aero/profile/PhillipOwens
If torque values were not important there would not be a table of values for them listed in the FAA maintnance manual. Yes they are important as they control the stretch of the fastener under load and prevent the attached nuts from backing off due to vibration and other causes. ARP fasteners has made an exhaustive study of torque and torque values, while primarily based upon race cars the results are the same. They provide a special torque lube for fasteners that allow you to create the correct…
If torque values were not important there would not be a table of values for them listed in the FAA maintnance manual. Yes they are important as they control the stretch of the fastener under load and prevent the attached nuts from backing off due to vibration and other causes. ARP fasteners has made an exhaustive study of torque and torque values, while primarily based upon race cars the results are the same. They provide a special torque lube for fasteners that allow you to create the correct specified torque each and every time as long as you are using a calibrated torque wrench. Remember, you will not be able to pull over and stop for repairs at 8,000 feet if something fails or falls off. The torque value is listed for the fastener based upon size. Hope this is some help. If you have a beam type torqu…tag:zenith.aero,2011-10-30:2606393:Comment:1713502011-10-30T18:05:43.480ZPaul Bonaserahttps://zenith.aero/profile/PaulBonasera
If you have a beam type torque wrench, ck the torque required to turn the nut BEFORE it bottoms out on the washer. You then add this torque to the listed value for your final torque.
If you have a beam type torque wrench, ck the torque required to turn the nut BEFORE it bottoms out on the washer. You then add this torque to the listed value for your final torque.