Does anyone use Corrosion protection on the Aluminum of the Airframe?

Views: 1138

Reply to This

Replies to This Discussion

Although the 6061T6 is more resistant to corrosion than other alloys, likely the majority of builders use some form of corrosion protection. This seems to range from spraying the entire interior with zinc chromate (toxic stuff!) to just using it on mating surfaces. Zenith sells "Cortec," a supposedly environmentally friendly water-based primer. You can thin it with water to a brushable consistency and if not applied too thickly, it dries relatively quickly. Caleb told me it is OK to join mating surfaces while the Cortec is still wet,  but be careful since when it dries, it acts much like a glue and it can be difficult to re-position or remove parts after drying! (Don't ask me how I know! Ha!) The biggest criticism I have of Cortec is that once it dries, it is near-invisible and therefore easy to forget whether you've primed something or not ... wish they would dye it!

I'm in a moderate, temperate climate, so I chose to use the Cortec on mating surfaces. Someone planning to install floats and operate on salt water might opt for far more protection and someone in the desert might opt to use none at all!

John

N750A

Thank you John for the information, I am just trying to put everything in order before order my kit.

I almost have my wood working shop re-laid out. I just finish making a 12 foot long work table. Trying to be ready before the kit comes. I will check out Cortec, because I don’t it to be ruin in, say 10 years.

Tony

I live inland and not near a body of water. I plan to use a corrosion protector on joining surfaces only. At this point I have used and plan to continue use of Cortec for that purpose. As John has already pointed out, Cortec makes a dandy glue. This can be good news or bad news. As long as you are not gonna take that area apart it is good news. Otherwise, you have a problem. When I helped open up my friend's 601XL for the upgrade process we learned of the problem -- hard to get things apart. Even harder to get them apart without putting permanent creases into the aluminum. With care you can do it, but be careful.

Hi Bob,

If Cortec was full dry before assembly, wound it vulcanize together?

Tony

I'm not crazy about Cortec...

Every inch of my build is covered in Zinc Oxide or Zinc Chromate.  The Chromate is WAY better (it sticks better and won't scratch off, in fact overspray after it dries is almost impossible to get rid of, even with acetone or MEK!) but it's getting harder to find and expensive when you do + it's kinda toxic!!! :0

I bought Zinc Oxide in the gallon size and sprayed the skins and parts with an automotive sprayer.  Smaller parts that needed spraying as I went I used spray bombs.  The inspectors up here expect some kind of corrosion protection.  At the very least some form of protection should be sprayed on any surface that is mated to another! The spray bombs work well for this, and Zinc dries pretty fast. 

Hi Mark,

Thank you for replying,

I am familiar with Zinc Chromate, and it is on HAZ Mat list. But allot items are now days. I am checking out what else is out there of airframes.

Thank you,

Tony

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service