Building Hints, Tips and Tricks. We invite you to share you "building tips, hints, and tricks" in this new discussion forum.
Note: This is non model specific forum: If you have a building tip, hint, and trick that is specific to a model please post to model specific forums.

Views: 6863

Reply to This

Replies to This Discussion

Y is Y/8 of an inch.... except when it is 10 then it is 1 inch and when it is 20 it is 2inches... so a Y of 4 is 4/8 or 1/2inch and there is no Y of 8 because that would become a 10, basically counting in base 8 (or 1/8ths of an inch...)!

Workbenches are always very personal, but here is Ghana we have to think a little bit laterally to achieve our concepts.

We can get hold of plywood and the design shown here was completed using 5 and a half pieces of 8'x4' plywood some scraps of pine from our kit crate (thanks Zenith for using great wood, well dried and straight) and 3 pieces of 2" (50mm) square section each 18' long, not to forget a few screws left over from a roofing job (self tapping) and some screws from the Zenith crate (thanks again Sebastien).

Our finished 20' x 4' bench is great. It gives us space to lay out parts and to work at the same time, and because it is set out from the wall we can walk all around it, which was a problem on our first bench.

I realize that we could have put storage inside each of the three plinths, but that is not a major issue, at this time. The two trainee aircraft technicians (Jennifer and Patricia) that made this bench with Jonathan wondered about using their new skills on making a new set of Kitchen cabinets for Elizabeth!!! Jonathan objected.on the grounds that getting the medical aircraft built and operational must come before the Kitchen cupboards (Elizabeth understands, as always!)
Good idea, agree about the storage space. How do you adjust it to make it level??
Firstly, try to make sure the the floor is level (we built the workshop - including casting all of the blocks ourselves from sand and cement) then, make sure that all of the plinths are the same, small adjustments can be made on the inserted 2"x4" and a good eye+level. If on installation there are adjustments to be done use some 2"x2" scraps of sheet aluminum or other shims under the steel bars, then if your plywood surface is wonky after that shim it where you bolt it down. If necessary add a simple 6" x 6" ply joint with similar packing.

Total time to build with me and two girls - 4 hours. (we have a power saw). The steel tubes were painted by Matthew (our son) during the build and were dry ready to install by the time everything was in place in the workshop. Installation and finishing about 1 hour. It really is good to have 20' to work on - but do draw a center line down the middle and mark off each meter length along the sides..
Jonathan and Elizabeth Porter - Thanks for using photos in your posts - this helps to illustrate your points well!
Radiator installations: I am not sure about all of the range but I know that on the 701 Rotax installation the piece of radiator hose we are supposed to 'discard' has a good use. It can effectively route away from the gear box when suitably cut and joined with an appropriate aluminum tube and two clips...

Any Hints/Tricks/Tips on keeping the upper skin of the wing from buckling/Tin-canning?? I called the factory yesterday, they recommended adding stiffeners between the ribs...I did that and it inproved the appearance.....any of ya all had any similiar problems? I still have the right wing to cover.

Ben

(PS I LOVE my sharpies...I'm especially fond of the short stubby ones...they are sooo cute!!!)
A friend uses .020 inch skin in place of .016 in rebuilding. He has not flown it yet, so I do not know the result. The 701 I bought is of and earlier light weight version. It flies alright, with heavy buckling noise in any cross wind. It does not have any of those stiffener installed between wing ribs. On rebuilding, I glue thick styrofoam wing ribs between 6061-T6 ones. Foam sheets are cheap and foam ribs are easy to make, plus lighter than the 6061-T6 stiffeners doing the same job. The only down side I foresee is that if I have to rework the wing I have to fight my way through foam and glue.

For fuselage. my 701 has strips of light wood glued in a couple of X shapes across the rear fuselage section. But they are not enough to resist buckling. I will replace wood with aluminum angle.

You may get expert advice from an EAA chapter near you.
Ben,

Another novice opinion.
After the above comment, I thought about foam core sandwiching and went ahead for a small experiment by gluing a piece of 10 m.m. styrofoam to a piece of .016" wing skin sheet, with 10 m.m. spacing between glue lines. Leaving it overnight to dry, the composite skin becomes a little more difficult to flex inward, and much more difficult to flex outward.

I have yet to find some simple tool and technique to apply glue evenly between foam sheet and aluminum sheet before trying it with my wings still under rebuilding.
Attachments:
Sounds like a reasonable idea (look at the Sherwood Ranger) - but what about fire risk, what if it comes unstuck, etc - Also, just check that you do not have ants that like the kind of foam you use. We have an aircraft with foam in the wings (not a CH) and the ants come and carry it off like snow flakes or bits of dandruff to their nest to make toys for the other ants!! Consequently, on soundproofing and cushions we try to only use foams we know are not attractive to the local insects!

G'day Champ,

3M Trim adhesive works a treat.  You spray it on both surfaces, let it dry, then push them together.

 

Cheers,

Paul.

Thank you, Paul.

 

I have got a can of 3M spray adhesive. I will try it tomorrow for the bottom of my battery box. 

 

Champ

RSS

New from Zenith:

Weather Maps


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, power distribution panel, Approach Fast Stack harnesses, Dynon and Garmin avionics, and more.


New Custom Upholstery Kits for your Zenith Aircraft:

Zenith Vinyl Upholstery Kits


New Zenith Apparel from EAA:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz.

Builder & Pilot Supplies:

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

 

Zenith transition and Sport Pilot training:

Quality Sport Planes
Cloverdale, California:

Wheels & Wings

Pro Builder Assistance

© 2018   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service