Has anyone broken a nose wheel bungee on their Zodiac XLB? This morning while flying Young Eagles the bungee on the nose gear broke after landing and during taxi on a semi rough grass strip in Michigan 55G. The rods through the firewall prevented the prop from striking the ground.

I wasa able to get to a hardware store and buy some rope, duct tape, bulk bungee cord and was able to takeoff and land at my home airport. Does this qualify me for the Red Green awards? ;-)......


Any thought on limiting the suspension travel to prevent this from happening again?

Views: 1440

Reply to This

Replies to This Discussion

Damn near Ron.  Last year at Oshkosh, they taxied me for about a mile on bumpy grass.  I thought it a good idea to inspect everything under the cowl and found that I was hanging by a few rubber threads.  Al Beyers was kind enough to lend me (off of his own plane) a stop collar that would prevent me from having a prop strike if the bungee actually broke.  THe collar is about 2 1/2" and is a must in my opinion if you have one of the earlier kits that did not include a stop ring.  I departed oshkosh and made very very gentle landings until I got to Mexco missouri and replaced the bungee at the zenith factory!  They let me use their tools and helped where they could.

Here's the funny thing, 100 hrs later on the hobbs I found myself with a  similarly frayed bungee.  It is very obvious to me that this is not the result of the bungee being over stretched, rather a bit of rather sharp metal cutting in and prematurley wearing on the bungee.  THis time I really softened the edges, and even wrapped everything that is remotely sharp in a special tape.  I really think this time I wont have any further issues, but this will always be somethign  I monitor every time I open up the cowl.

On the older kits (mine is an HD) there was no stop ring and if the bungee pops you are majorly SOL and would certainly prop strike.  I also considered that if I did prop strike, I'd be in a really likely scenario for a flip and (extremely nose low) and due the prop (what was left of it ould likeley veer to the left quickly) McMaster carr sells what is called a Split collar shaft. it is 2.5" in diameter and will hopefullly never be used.

I bet you did like I did on that duct tape and bungee and made what I still refer to as the imaculate landing.  I touched down the softest I ever had when the heat was really on!

Here is what I used, I cant recall the exact one I bought, but you catch my drift.  You're lucky the rods had your back!

Real lucky in my opinion.

http://www.mcmaster.com/#shaft-collars/=ipht1b

Hmmm....those Mcmaster collars seem a bit more safe than the skinny ring welded on my nose gear. Anyone know how well that little collar on my 750 would hold up?

That little ring appears very securely welded on my nosegear - I suspect it would destroy the bearing block before deforming much. I would speculate that if there was a catastrophic failure, it would result in the bearing block splitting apart by stripping all the bolts out. That would take an awful lot of force ... my guess is that in that instance, the nosegear collapse would be the least of your problems!

Wasn't there a notice of some bungees being defective? Seems like there is a color-code to the threads on the surface of the bungee - I don't remember the details, but mine was not colored like the defective ones.

Perhaps someone who has lost a bungee with a ring welded on the nosegear can tell us if they had any further damage?

John, the little ring is not there. And that is the fault of the manufacturer, which is me. I left it off and over stretched the bungee is what it looks like. I'm stopping but the welding supply today and getting the 1/8 wire to form and install the ring at 95mm below the tee bar bolts heads just like the print said I should have.

Once again, I find myself happy to be building a taildragger instead of a nose dragger..............  :)

I was dragging my tail in today... Even through my flight bag way in the back to assist.

Ron, Bob DePriest up in Hernando, MS had the same trouble with his bungee.

See this current discussion on the 750 forum. Appears to be bungee problem regardless of model.
http://www.zenith.aero/group/stolch750/forum/topics/nose-gear-bunge...

Jeff

Hi Folks,

I just went over 60 hours on my 701 and am reading all this about the bungee problem.

Believe me the next time I go out I"m gonna pull the lower cowl, set her on the tail and give it all a good look.

I remember reading about someone using a split collar bolted on the nose gear to limit travel. Has anyone determined a dimension that would be "right" from the bottom of the nylon bearing for the 701? I'm talking about providing enough travel and yet protect the prop from a ground strike if the bungee fails.???

 

From the looks of things I just don't want to trust it all to the "color of the threads" in different manufacturing batches.

 

Thanks

 

Phil Smith

CH-701 Buhl ID

RSS

New from Zenith:

Zenith Planes For Sale 
 

Classified listing for buying or selling your Zenith building or flying related stuff...


Custom Instrument Panels
for your Zenith
:

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, Dynon and Garmin avionics, and more.


Zenith Homecoming Tee:


Zenair Floats


Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz


Builder & Pilot Supplies:

Aircraft Insurance:

 
 

West Coast USA:

 
Pro Builder Assistance:

 

Transition training:

Lavion Aero

K&S Aviation Services

Aircraft Spruce & Specialty for all your building and pilot supplies!

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

© 2024   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service