Going out for my second sortie and while in the climb with full power I got that hot oil smell and a bit of mist in the cabin.  Closed the heat control valve, reduced power and "bee-lined" to the airfield with good oil pressure while venting the cabin. Taxied in with good oil pressure to a shutdown in front of my hangar.

What a mess...I was down to just below the min line on the dipstick.  Luckily I have another oil cooler (AERO-Classics) on the shelf which I've been meaning to put on since this summer.  I've heard bits and pieces regarding the quality of the UL provided oil cooler and wanted to see if a different cooler might help out with cooling (and quality?)  Anyway, something to think about I guess...

Views: 1556

Reply to This

Replies to This Discussion

The builder of my plane also had the ULpower supplied oil cooler "blow" on him.  He installed the 10 row AERO Classic; no issues since.  These engines always seem to have real warm oil, and cool CHTs.  I'm sitting at a little under 450 hrs on the 350iS now, and it's been great.  But seems the starter solenoid is starting to act up a bit..  Keep up the fun.


  Just have to ask, how many hours did the oil cooler have on it when it died, and how is the replacement attached? Fixed solid or rubber shock?


Hi, Ralph

I sold the 750 to Coner, but in the first 80 hour I lost two ULP oil cooler. They both had two rubber mounts. I changed to a Aero Classic with four rubber mounts. Conor

bought the plane with around 186 tt, and has 450tt now.

Ron Simonsen 

Dave just curious as to what your oil pressures are averaging with the UL unit vs The new unit? . I’m getting 90+ psi at cold startup and at Temp I’m averaging around 40psi at idle with the ULP .

Phil, those numbers are similar to mine with the ULP cooler. 90 PSI initially dropping to 60 during the 1350 RPM warm up. Cruise at 2500 RPM yields about 42 PSI on the oil pressure.  I've only got one flight in with the new cooler so far and the data is not much different.  87 PSI at 1500 RPM during warm up. 41 PSI at 2500 RPM cruise and about 20 PSI at RPM less than 900.  SavvyAnalysis makes reviewing the data easy!!  Hope this helps.


New oil cooler with rubber edge trim installed...

Add one more data point to the blown oil cooler.  Mine went south on my trip back from Oshkosh.  Small pinhole in the front.  I was down to about a quart and a half when I landed.  Just a faint burning smell.  I had no other drop in oil pressure until I landed.  Fueling up the plane and oil dripping every where.  Looked just like David's picture without the skis.  Roger was able to hook me up with a new cooler to get back to Paris, Texas. Many thanks to him and Joyce at Zenith.   Uneventful flight back.  Will be ordering a 13 row aeroclassic later today.  I was planning on switching it out at my 100 hr oil change.  I had about 70 hrs on the engine.  My temps have been in the 198-203 range.   Wondering if  I should pre weld my muffler pipe before it falls off.   I left the oil cooler back with Roger at Zenith as he wanted to have it tested.  Will post with any results that I get. 

I uploaded a couple videos to my YouTube channel.  1960drfred. 

This should be the link. Oil pressure is 67 at 2600 rpm. Temps 195. I think it dropped my oil temp about ten degrees.  There also is also a video on the channel about the fiberglass repair. Whatever you use as a form, just cover it with clear packing tape so it will release from the epoxy mix.  




New from Zenith:

Zenith Planes For Sale 

Classified listing for buying or selling your Zenith building or flying related stuff...


Weather Maps

Custom Instrument Panels
for your Zenith

Custom instrument panels are now available directly from Zenith Aircraft Company exclusively for Zenith builders and owners. Pre-cut panel, power distribution panel, Approach Fast Stack harnesses, Dynon and Garmin avionics, and more.

Custom Upholstery Kits for your Zenith Aircraft:

Zenith Vinyl Upholstery Kits

Zenith Apparel from EAA:

Zenair Floats

Flying On Your Own Wings:
A Complete Guide to Understanding Light Airplane Design, by Chris Heintz

Builder & Pilot Supplies:

How to videos from HomebuiltHELP.com

Developed specifically for Zenith builders (by a builder) these videos on DVD are a great help in building your own kit plane by providing practical hands-on construction information. Visit HomebuiltHelp.com for the latest DVD titles.

Aircraft Insurance:


West Coast USA:

Transition Training:

Pro Builder Assistance

Pro Builder Assistance

Aircraft Spruce & Specialty for all your building and pilot supplies!

© 2019   Created by Zenith.Aero.   Powered by

Badges  |  Report an Issue  |  Terms of Service