Airspeed not accurate - Zenith Aircraft Builders and Flyers2024-03-29T15:50:29Zhttps://zenith.aero/forum/topics/airspeed-not-accurate?commentId=2606393%3AComment%3A358728&feed=yes&xn_auth=noThere is a chart of pressure…tag:zenith.aero,2014-05-27:2606393:Comment:3587282014-05-27T23:02:18.311ZRobert Staceyhttps://zenith.aero/profile/RobertStacey
<p>There is a chart of pressure versus airspeed. You could use an accurate pressure gauge or manometer to ensure your indicator is calibrated correctly. ie showing correct airspeed for a couple of calibration pressures. After that it is only a matter of getting the end of the tube to impact the air squarely ant it should be dead on. </p>
<p>my 2 cents</p>
<p>Bob </p>
<p>There is a chart of pressure versus airspeed. You could use an accurate pressure gauge or manometer to ensure your indicator is calibrated correctly. ie showing correct airspeed for a couple of calibration pressures. After that it is only a matter of getting the end of the tube to impact the air squarely ant it should be dead on. </p>
<p>my 2 cents</p>
<p>Bob </p> Glenn,
I tried the test of…tag:zenith.aero,2014-05-27:2606393:Comment:3587182014-05-27T17:44:14.454ZDavid Gallagherhttps://zenith.aero/profile/DavidGallagher
<p>Glenn,</p>
<p> </p>
<p>I tried the test of putting a "bump" in front of, or behind, the static holes on the Zenith supplied probe to change the static pressure sensed by the ports. I had an issue with GPS vs. indicated altitude being about 200' off at 4500msl and groundspeed vs. airspeed off by about 10 mph. I put a few 1/4" wide wraps of speed tape in front of the static holes and then tried it behind the holes. I can't remember now, but one exacerbated the issue and the other improved…</p>
<p>Glenn,</p>
<p> </p>
<p>I tried the test of putting a "bump" in front of, or behind, the static holes on the Zenith supplied probe to change the static pressure sensed by the ports. I had an issue with GPS vs. indicated altitude being about 200' off at 4500msl and groundspeed vs. airspeed off by about 10 mph. I put a few 1/4" wide wraps of speed tape in front of the static holes and then tried it behind the holes. I can't remember now, but one exacerbated the issue and the other improved it. I am now well under 100' of altitude and 4 mph of speed difference. That was good enough for me and day VFR flying so I stuck with it.</p>
<p> </p>
<p>Good luck,</p>
<p> </p>
<p>Dave</p> Using the Zenith supplied pit…tag:zenith.aero,2014-05-27:2606393:Comment:3586052014-05-27T11:46:35.060ZBob McDonaldhttps://zenith.aero/profile/BobMcDonald
<p>Using the Zenith supplied pitot is the source of the problem.</p>
<p>Spend the money for the quality Dynon pitot (unheated unless flying IFR) and your airspeed issues.</p>
<p>My experienced 2 cents.</p>
<p>Using the Zenith supplied pitot is the source of the problem.</p>
<p>Spend the money for the quality Dynon pitot (unheated unless flying IFR) and your airspeed issues.</p>
<p>My experienced 2 cents.</p> I had leaks where the pitot (…tag:zenith.aero,2014-05-27:2606393:Comment:3584862014-05-27T04:22:25.016ZChristopher Jon Brownhttps://zenith.aero/profile/christopherjonbrown
<p>I had leaks where the pitot (zenith) attaches to the rubber tubing they supply, added a brass compression union here and all fixed. Same thing where it connected coming in from the wing to the fuselage, added 90 degree brass compression fitting all ok. Also had to add some teflon tape where the fitting attaches to the instrument, then perfect. Took a piece of surgical tubing and rolled it up as it was attached to the pitot tube with the EFIS on (MGL) and pinched it closed once I was at 90…</p>
<p>I had leaks where the pitot (zenith) attaches to the rubber tubing they supply, added a brass compression union here and all fixed. Same thing where it connected coming in from the wing to the fuselage, added 90 degree brass compression fitting all ok. Also had to add some teflon tape where the fitting attaches to the instrument, then perfect. Took a piece of surgical tubing and rolled it up as it was attached to the pitot tube with the EFIS on (MGL) and pinched it closed once I was at 90 MPH and it held for 10 minutes easily, then tested it at 57 MPH and worked perfectly here also. I was amazed I had so many leaks, I thought it would all seal how they supplied it! How did it pass the pitot static/ transponder test?</p> Good catch on the Knots / MPH…tag:zenith.aero,2014-05-26:2606393:Comment:3586872014-05-26T16:22:50.392ZGlenn Johnsonhttps://zenith.aero/profile/GlennJohnson
<p>Good catch on the Knots / MPH. Both are in knots. I was doing my speed checks at 4,000 feet so went up today and stayed @ 1,000. Came up 8 lower indicated vs GPS. For my GPS I fly 4 different heading S,E,N & W and take the average. With the static open in the cabin I "should" get a higher indicated reading from what I have read. </p>
<p></p>
<p>As for vents etc, nothing close as it is located in the middle of the fuel tank. I will check the static line from the EFIS back today by…</p>
<p>Good catch on the Knots / MPH. Both are in knots. I was doing my speed checks at 4,000 feet so went up today and stayed @ 1,000. Came up 8 lower indicated vs GPS. For my GPS I fly 4 different heading S,E,N & W and take the average. With the static open in the cabin I "should" get a higher indicated reading from what I have read. </p>
<p></p>
<p>As for vents etc, nothing close as it is located in the middle of the fuel tank. I will check the static line from the EFIS back today by blowing in the EFIS end after I disconnect it there. I know the pitot is clear as I disconnected it at the EFIS and blew into the pitot end to confirm it was the correct line before I pumped it up to 75 PSI with a bike pump and checked for leaks. Found no bubbles at any connections and found I lost about 2 PSI in 15 minutes. Considering the low operating pressure I don't see that loss as an issue. </p>
<p></p>
<p>Forgot to check the altitude today, so that is on my check list next flight. I will also try putting a sleeve on the pitot next flight to lengthen it by about a foot which will put it about even with the leading edge.</p>
<p></p>
<p>Thanks for the tips.</p> Hi
Unfortunately I have no re…tag:zenith.aero,2014-05-26:2606393:Comment:3582442014-05-26T03:54:07.471ZFrançois Balauxhttps://zenith.aero/profile/FrancoisBalaux
<p>Hi</p>
<p>Unfortunately I have no real solution, but a few suggestions to isolate the problem.</p>
<p>There is a zero pressure calibration in the troubleshooting guide of the installation guide, maybe you could try that.</p>
<p></p>
<p>Is your altitude reading the same on the Dynon and your GPS at every speed/attitude/altitude? I guess if your altitude is always correct your static line must be OK. If it varies the problem is the instrument or the static line, but not the…</p>
<p>Hi</p>
<p>Unfortunately I have no real solution, but a few suggestions to isolate the problem.</p>
<p>There is a zero pressure calibration in the troubleshooting guide of the installation guide, maybe you could try that.</p>
<p></p>
<p>Is your altitude reading the same on the Dynon and your GPS at every speed/attitude/altitude? I guess if your altitude is always correct your static line must be OK. If it varies the problem is the instrument or the static line, but not the pitot.</p>
<p></p>
<p>I am not 100% sure, but I don't think it is a leak problem. A leak should be more important as pressure rise, so the difference in reading should be larger as speed increase. This is not the situation you describe. </p>
<p></p>
<p>So if the static line is ok the problem can be the instrument or the position of the pitot.You could probably put a sleeve around the pitot to make it longer so the opening is in front of the wing, just in case there is turbulence at its current location.</p>
<p></p>
<p>If all these fail I would have a big doubt on the instrument itself. I would remove it from the airplane and test it in my car with a passenger holding a flexible hose connected to the D100 by the window,</p>
<p></p>
<p>I hope this helps...</p>
<p>Francois</p>
<p></p> A couple of thoughts. Are bo…tag:zenith.aero,2014-05-26:2606393:Comment:3583182014-05-26T03:46:44.666ZDan Dempseyhttps://zenith.aero/profile/DanDempsey
<p>A couple of thoughts. Are both set to the same units? knots/mph?</p>
<p>I just mention that because 80 knots is 92 MPH... could be a coincidence.</p>
<p>Could there have been a tail wind each time? GPS gives you ground speed, IAS gives air speed.</p>
<p>Any chance mud dobbers have plugged up the pito?</p>
<p>I know when I planned the placement of my pito I made sure to keep it away from the gas tank vents or other disturbances. Did it read correctly in the past?</p>
<p>Good to hear from…</p>
<p>A couple of thoughts. Are both set to the same units? knots/mph?</p>
<p>I just mention that because 80 knots is 92 MPH... could be a coincidence.</p>
<p>Could there have been a tail wind each time? GPS gives you ground speed, IAS gives air speed.</p>
<p>Any chance mud dobbers have plugged up the pito?</p>
<p>I know when I planned the placement of my pito I made sure to keep it away from the gas tank vents or other disturbances. Did it read correctly in the past?</p>
<p>Good to hear from you again Glen. Glad you've got the plane going again.</p>
<p> </p>